Bedienungsanleitung Edilkamin Firebox Deco (Seite 19 von 24) (Englisch)

810849

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

Lighting a cold fifi replace

1. Check the existing ash bed is not too high. If the

ash bed is too high, there is a danger of opening the

door of the fifi replace to add wood and possible

brazier fragments fall out of the fifi replace.

2. Position the adjustment lever of the valve in the “total

opening” position . The air for combustion will flfl ow

intensely to the wood in the fifi replace, to quickly reach

good combustion.

3. place the wood in the fifi replace without excessively

squashing it in. Position a fifi relighter between the

wood logs and light. Never user materials such as

petrol, alcohol and similar to switch on.

4. At this point, close the door and monitor it for a few

minutes. If the fifi re should extinguish, slowly open the

door, re-position another fifi relighter between the logs

and light again.

Lighting a hot fireplace

When should wood be added? When the fuel is

almost completely consumed to embers. With the

glove supplied, slowly open (to avoid formation of

vortexes that can cause smoke to exit) the door.

Add the desired wood to the fifi replace, locating it on

the existing embers (within the quality limits indicated

in the technical table).

Product functioning changes with the chimney flue

draft and adjustment of the air valve in combustion.

Functioning with initial low draft

To extract air for combustion and discharge the

smoke, the fifi replace needs a draft to be exerted on

the chimney flflue.

If the draft is weak, initially light a “starter” fifi re using

small sized lighting material.

Once the correct draft is restored, you can add the fuel.

As with all the products, the wood product heats and

cools during the various phases. This would lead to

normal dilation. Such dilation can cause slight settling

noise, which is not a reason for dispute.

USER INSTRUCTIONS

FUEL

The product was designed to burn wooden logs or

sawdust briquettes.

Use dry wood logs (max. humidity 20%)Use logs The

use of damp wood would cause the product and the

flue to get dirty, the risk of smoke and a lower yield

than that declared.Each type of wood has different

characteristics that also influence combustion yield.

The data outlined on this manual are with wood used

during certifi cation.

In general wood can have a heat of combustion up to

4.5 kWh/kg while cut fresh it has heat of combustion

around 2 kWh/kg

In general, beech or elm is recommended, or however

class A1 wood according to UNI EN ISO 17225-5

Attention to prolonged use of wood with aromatic oils

(e.g. eucalyptus). Cast iron parts can deteriorate

Use the recommended quantities of wood:

Overloading causes overheating, resulting in damage:

• possible deformation of the inner parts;

• possible irreversible changes to the colour of the

paint on the metal parts for which Edilkamin or the

retailer cannot be held liable.

To respect the environment and safety, do NOT burn,

among other things: plastic, varnished wood, coal and

bark waste.

Do not use the product as an incinerator.

Use of these fuels also nullifi es the guarantee.

First switch on phases

• Ensure you have read and understood the content

of this manual

• Remove all the inflfl ammable parts from the

product (manuals, labels, etc.). In particular

remove any labels from the glass. If they melt, they

would irreversibly damage the glass.

For initial switch on of the fifi replace, always use the

smallest logs. Use larger wooden logs to raise the fifi

re.

Always locate the wood deep in the fifi replace, al-

most in contact with the rear wall, so that even if they

slide they won’t come in contact with the glass.

There may be a slight smell of paint the fi rst few

times it is ignited, however, this will disappear quickly.

Use always the glove supplied to touch

hot parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Firebox Deco Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Firebox Deco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info