Bedienungsanleitung Edilkamin Flamma (Seite 17 von 24) (Englisch)

810908

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

FIRST SWITCH ON PHASES

• Ensure you have read and understood the content

of this manual

• Remove all the inflammable parts from the product

(manuals, labels, etc.). In particular remove any

labels from the glass. If they melt, they would

irreversibly damage the glass.

For initial switch on of the fireplace, always use the

smallest logs. Use larger wooden logs to raise the fire.

Always locate the wood deep in the fireplace, almost in

contact with the rear wall, so that even if they slide they

won’t come in contact with the glass.

To open the door

(to load wood and clean the glass)

Use the fixed handle - make sure to use the provided

glove if the appliance is still hot.

Before closing the door, make sure the latch (*) is in

the horizontal position.

If it is not, the door will not close completely.

Lighting a cold fireplace

1. Check the existing ash bed is not too high. If the

ash bed is too high, there is a danger of opening the

door of the fireplace to add wood and possible brazier

fragments fall out of the fireplace.

2. Position the adjustment lever of the valve in the “total

opening” position. The air for combustion will flow

intensely to the wood in the fireplace, to quickly reach

good combustion.

3. place the wood in the fireplace without excessively

squashing it in. Position a firelighter between the wood

logs and light. Never user materials such as petrol,

alcohol and similar to switch on.

4. At this point, close the door and monitor it for a few

minutes. If the fire should extinguish, slowly open the

door, re-position another firelighter between the logs

and light again.

Lighting a hot fireplace

When should wood be added? When the fuel is

almost completely consumed to embers. With the

glove supplied, slowly open (to avoid formation of

vortexes that can cause smoke to exit) the door. Add

the desired wood to the fireplace, locating it on the

existing embers (within the quality limits indicated in

the technical table).

Stove functioning changes with the chimney flue draft

and adjustment of the air valve in combustion.

Functioning with initial low draft

To extract air for combustion and discharge the

smoke, the fireplace needs a draft to be exerted on the

chimney flue.

If the draft is weak, initially light a “starter” fire using

small sized lighting material.

Once the correct draft is restored, you can add the fuel.

ISTRUCTIONS FOR USE

As with all the products, the wood stove

heats and cools during the various phases.

This would lead to normal dilation. Such

dilation can cause slight settling noise,

which is not a reason for dispute.

There may be a slight smell of paint the

first few times it is ignited, however, this will

disappear quickly.

VENT

In the first few days of use, you may need

to use the vent to bleed all the air out of the

circuit. Remove the ceramic top panel to

access the internal vent valve.

The handle is fixed.

DO NOT attempt to turn it, simply pull it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Flamma Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Flamma

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info