Bedienungsanleitung Edilkamin Forte 2 Up (Seite 5 von 16) (Englisch)

810856

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

INSTALLATION INSTRUCTIONS

Important warnings

As well as that indicated in the pre-

sent document, bear in mind the UNI

rules:

- n. 10683 - wood heat generators:

installation requirements

- n. 9615/90 - calculation of the

chimney internal dimensions.

In particular:

- before starting any mounting opera-

tion, it is important to verify the

compatibility of the plant as establi-

shed by the UNI 10683 rule in para-

graphs 4.1/ 4.1.1 / 4.1.2.

- once mounted, once mounted, the

installer must “start up” the plant and

issue the documentation requested in

the UNI 10683 rule, respectively in

paragraphs 4.6 and 5.

Before installing the cover, verify the

correct functioning of the connections,

the controls and all moving parts.

The verification must be carried out

with the chimney having been on for a

few hours, before covering the hearth,

in order to eventually intervene.

Therefore, the finishing operations

such as for example:

- manufacture of the false hood

- mounting of covering

- carrying out stripping, painting, etc.

must be carried out once tested with

positive result.

Therefore, Edilkamin does not

answer for burdens deriving from

both demolition and reconstruction

interventions, even if subsequent to

replacing hearth pieces which resul-

ted faulty.

Calibration and start up to be carried

out by the dealer.

Vorwort

• The FORTE UP2 hearths must be

installed keeping to the following

instructions, as the safety and plant

efficiency depend on the correct

installation.

• Carefully read the present instruc-

tions before mounting.

•EDILKAMIN declines any responsi-

bility for eventual damages deriving

from the non compliance with the pre-

sent instructions and, in case, any war-

ranty right will be void.

• The FORTE UP2 hearth is supplied

already assembled on non returnable

pallet. The inside covering of the

hearth is supplied already installed.

•A model identification label is

applied under the hearth hatch; the

label can be seen until the hearth is

covered. The model identification

number is indicated in the documenta-

tion supplied with the product.

Building protection

All the building surfaces near the

hearth must be protected against over-

heating. The insulating measures to be

adopted depend on the type of surfaces

present and how they are made.

Hot air outlets / Grillsr

The hot air outlets must be placed at a

minimum distance of 50 cm from the

ceiling and 30 cm from the furniture.

Position the grills or the air outlets at

the highest point of the covering, in

order to avoid heat accumulating insi-

de the same covering. Position the

grills or the air outlets so that they can

be easily accessed for cleaning.

Heating insulation

The insulating layers must not have

joints and have to be overlapped. The

thickness of the insulating material

must be of at least 3 cm.

Ornamental beams

The realisation of eventual wood orna-

mental beams in front of the hearth

covering is allowed only if they are

outside the radiation field, at a distan-

ce of at least 1 cm from the same cove-

ring. The air space which isolates the

ornamental elements and the covering

must be such not to accumulate heat.

The wood ornamental beams cannot

be integrating parts of the building.

Floor opposite the hearth

Floors made with fuelling materials

must be protected by a sufficiently

thick, non fuelling cover.

The floor protection must be equal to:

frontally:

- the corresponding height of the fire

surface from the floor plus 30 cm and,

in any case, min. 50 cm

laterally:

- the corresponding height of the fire

surface from the floor plus 20 cm and,

in any case, min. 30 cm.

In the radiation field of the hearth

The structural elements built with

fuelling material or which present

fuelling components and the furniture

must be positioned at a minimum

distance of 80 cm from the hearths

mouth, in all three directions: front,

upper and side.

Should such elements or furniture be

screened by a ventilated anti-radiation

protection, it will be sufficient to

respect a distance of 40 cm.

Outside the radiation field

The structural elements built with

fuelling materials or which present

fuelling components and furniture,

must be positioned at a minimum

distance of 5 cm from the hearths

covering.

In such air space, the air present in the

room must be able to circulate freely.

No heat accumulation must be created.

Electric lines

There must be no electric lines in the

walls and the ceilings, including the

hearth embedding area.

NOTE: The product is supplied with

two anti-corrosion discs (one on the

outside and one on the inside of the

combustion chamber). They must be

removed during unpacking and

disposed of as normal waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Forte 2 Up Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Forte 2 Up

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info