Bedienungsanleitung Edilkamin GORA (Seite 13 von 44) (Englisch)

810888

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

WATER CIRCUIT INSTALLATION

PLUMBING

The products are equipped with closed expansion

tanks.

If the expansion tank is built into the product, this

does NOT ensure proper protection against thermal

expansion caused by water in the entire system.

Therefore, installers should assess whether an

additional expansion tank is needed, depending on the

type of system.

ALL OTHER HYDRAULIC COMPONENTS MAY BE

INSTALLED WITHIN THE Boiler stove BY PURCHASING

A KIT OR IF PREPARED BY THE INSTALLER.

• Plumbing depends on the type of system.

• However, there are some “general rules”:

• The hydraulic system must operate at a pressure

between 1 and 1.5-2 bars at running temperature

(hot) in a closed vessel circuit.

• N.B.: The boiler stove SHOULD NOT be installed

in place of, for example, an open vessel installed

kitchen range without adjusting the expansion

system to closed vessel.

• The presence of an accumulator (tank) is

recommended but not mandatory. Its advantage

is that it releases the boiler stove from “sudden”

requests from the system and can be integrated

with other heat sources. It reduces fuel consumption

and increases the efficiency of the system. A puffer

of at least 20 l/kW is recommended.

• The return temperature of water to the boiler stove

must be higher than 50-55° C to prevent the forming

of condensation.

• An accumulator (tank) is needed to heat

lowtemperature radiant panels and must be installed

according to the panel manufacturer’s instructions.

• The material used in the circuit must be suitable to

withstand overheating.

• The installer must determine whether or not to use

conditioned products. In Italy, refer to UNI 8065-1989

(Water treatment in heating systems for civil use).

• Direct plumbing to the radiators prevents proper

operation, owing to the small diameter of their pipes.

We offer four internal kits (optional)

KIT R-FX

for installation without instant DHW production.

KIT R2-FX

For installation without instant DHW production with

system separator.

KIT RW-FX

for installation with instant DHW production Suggested

for 22 kW models only.

PRESS URE GAUGE

The boiler stoves have an electronic water pressure

gauge. There are no analogue pressure gauges.

The water pressure is shown on the display, (*) as

shown

in the diagram. An analogue pressure gauges can be

fitted as an optional extra.

VENT

During normal operation the stove is

vented automatically. The need for manual

venting can only be assessed at initial

start-up by the technician

make sure that the swivel (nut)

on the two boiler stove outlet

pipes is closed

The product looks like the image below without any

kits.

(*)

Real size templates are available for technicians.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin GORA Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin GORA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info