Bedienungsanleitung Edilkamin Kelly (Seite 39 von 208) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810817

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

INSTALLATION

SMOKE OUTLET

The stove must have its own smoke outlet (the smoke

cannot be discharged into a smoke flue used by other

devices).

The smoke exhaust is expelled through the 8 cm-diameter

outlet located on the back, right side or top. The smoke outlet

must be connected to outside by means of suitable steel pipes and

must be free from obstructions. The stove smoke discharge must

be connected with outside by means of steel or black pipes EN

1856 certified. The pipe line must be hermetically sealed. The

pipes must be sealed and insulated using materials that are resistant

to high temperatures(high temperature silicone or mastic). The

only horizontal section allowed may be up to 2 m long. It is pos-

sible to use up to two curves with a maximum angle of 90

° (with respect to the vertical axis). If the outlet is not fitted

into a chimney flue, a vertical section and a wind guard are requi-

red (reference UNI 10683). The vertical duct can be internal or

external. If the smoke channel is outside, it must be appropriately

insulated. If the smoke channel is fitted inside a chimney flue, the

latter must be suitable for solid fuel. If it is wider than 150 mm in

diameter it must be improved by entering a pipe that has a suitable

cross-section and is made of suitable material (e.g. 80 mm diame-

ter steel). All sections of the smoke duct must be accessible for

inspection. The chimney pots and smoke ducts connected to the

solid fuel appliances must be cleaned once a year (verify whether

a specific legislation exists in your country). Failure to regularly

inspect and clean the stove increases the probability of a fire occur-

ring in the chimney pot. In that case, proceed as follows: Do not

use water to extinguish the fire; Empty the pellet hopper; Contact

specialist personnel before reigniting the stove.

Refer to local regulations in the country of use for any-

thing that is not specifically covered in this manual. In

Italy, refer to standard UNI 10683 in addition to any

Regional or Local Health Authority regulations. If the

stove is to be installed in a block of apartments, consult

the block administration before installing.

VERIFY COMPATIBILITY WITH OTHER

DEVICES

The stove must NOT be installed in the same room as

extractors, type B heating appliances and other appliances

that may affect its operation. See regulation UNI 10683.

VERIFY THE POWER SUPPLY CONNEC-

TION (the plug must be accessible)

The stove is supplied with a power cable that is to be con-

nected to a 230V 50 Hz socket, preferably fitted with a

magnetothermic switch. In the event that the power outlet is

not easily accessible, provide a device to cut off the power

supply (a switch) upstream of the stove (must be provided

by the customer). Voltage variations exceeding 10% can

damage the stove (unless already installed, an appropriate

differential switch must be fitted). The electrical system

must comply with the law; particularly verify the efficiency

of the earthing system. The power line must have a suitable

cross-section for the stove’s power. An inadequate earthing

system can cause anomalies for which Edilkamin cannot be

held liable.

FIRE PREVENTION SAFETY DISTANCES

The stove can be attached directly to brick and/or plaster-

board walls. In the case of combustible walls (wood, for

example), you must install adequate insulation in a non

combustible material. You are required to adequately insu-

late the smoke exhaust pipe and the warm air channelling

pipe, as they reach high temperatures. All elements made

from combustible and/or heat-sensitive material located

adjacent to the stove must be arranged at a distance of no

less than 20 cm or otherwise be adequately insulated with

non combustible insulating material, and in any case mate-

rials can not be placed at less than 80 cm in front of the

stove as they are directly exposed to the heat radiating

from the hearth. Leave a suitable amount of space between

the element directly adjacent and the stove in order to

comfortably use the synoptic panel located on the left side

of the Kelly stove.

AIR INTAKE

There must be an air inlet behind the stove with a mini-

mum diameter of 80 cm². This must be connected to the

outside in order to guarantee sufficient air supply to the

stove for combustion.

A: insulated steel flue

B:minimum height of 1.5 m and in any case above the height of the roof gutter

C-E: air intake from inside room (minimum internal section: 80 cm²)

D: steel flue, inside existing brick-built chimney.

TYPICAL EXAMPLES

CHIMNEY POT

The main characteristics are:

- an internal cross-section at the base, which is the same as that of

the chimney flue

- an outlet cross-section which is no smaller than twice that of the

chimney flue

- its position must be high enough to catch the wind and avoid

downdraft areas in turbulent wind, it must be high enough to

catch the wind and avoid downdraft areas in turbulent wind.

ENGLISH

Fig. 2

Fig. 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Kelly Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info