Bedienungsanleitung Edilkamin Kikka Plus - 2016 (Seite 50 von 210) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

810777

Zoom out

Zoom in

Vorherige Seite

1/210

Nächste Seite

- 50 -

ENGLISH

POSSIBLE TROUBLESHOOTINGPOSSIBLE TROUBLESHOOTING

In the event of problems the stove stops automatically and runs the shutdown process and the display shows text regarding

the motivation of the shutdown (see the various alarms below).

Never pull the plug during shutdown on account of malfunction.

If the stove shuts down, you need to let the Switch-off procedure ﬁ nish before you can restart the stove.

Do not turn the stove on again before checking the cause of the malfunction and CLEANING/ EMPTYING the crucible.

INDICATION OF POSSIBLE CAUSES OF MALFUNCTION AND INDICATIONS AND REMEDIES:

1) Signalling: AL 01 fume probe faulty or disconnected

Problem: Shutdown due to faulty or disconnected fume probe

Actions: • Check the fume probe connection to the board: check the operation with a cold test (DEALER).

2) Signalling: AL 02 Room sensor fault (this is activated if the probe is faulty or disconnected)

Problem: Shutdown due to detected temperature anomaly

Actions: • Check the connection of the probe to the circuit board (DEALER)

• Check the operation of the sensor (DEALER)

3) Signalling: AL07 Thermal safety (this occurs when the safety thermostat, located on the pellet slide, trips due to over-

temperature in the pellet tank)

Problem: Excessive loading of pellets

Actions: Check operation of motor (DEALER)

4) Signalling: AL 08 depressurisation lacking (this occurs when there is not sufﬁ cient draft in the cold air intake pipe)

Problem: The screw feeder is stopped

Actions: • Check that the cold air pipe is not obstructed

• Check the pressure switch

• Check that the silicone tube is not clogged

5) Signalling: AL 09 Failure of fume expulsion motor (this trips if the smoke extraction speed sensor detects a fault)

Problem: Shutdown for smoke extraction speed fault detection

Actions: • Check smoke extractor function (devolution sensor connection) and board (DEALER).

• Check smoke channel for dirt • Verify the electrical system and earthing system.

• Check eletronic circuit board (DEALER).

6) Signalling: AL 10 Failed ignition (intervenes if a ﬂ ame fails to appear within a maximum of 20 minutes, or if ignition

temperature is not reached).

Problem: Turns off due to incorrect smoke temperature during ignition

Distinguish either of the following cases:

Flame does NOT appear

Actions: Check: - combustion chamber position and cleanliness;

- arrival of combustion air in the combustion chamber;- if the heating element is working (DEALER);

- room temperature (if lower than 3°C use a ﬁ relighter) and damp. - Try to light with a ﬁ relighter.

Flames appear, but AF appears on the display after Ar.

Actions: Check: (only by the Dealer)

- • fume probe operation (DEALER);

- start-up temperature setting in the parameters (DEALER).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Kikka Plus - 2016 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info