Bedienungsanleitung Edilkamin Lux (Seite 16 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810742

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 16 -

ENGLISH

COVERING INSTALLATION BIG/VIP

150

vite

Part. “Z”

ﬁ g. 1

ﬁ g. 11

ﬁ g. 4

ﬁ g. 2

ﬁ g. 3

150

150 150

150

ﬁ g. 8 ﬁ g. 9

ﬁ g. 10

57-58

bushings

screw

DETAIL. Z

detail. “Y”

INCLUDED HARDWARE:

2 M6x25 screws

2 M6x12 screws

4 silicone spacers for ceramic top

8 ﬂ at washers diam. 6

2 bushings

16 silicone spacers for ceramics

2 ceramic ﬁ xing plates

ASSEMBLING THE LATERAL TILES (ﬁ g. 1-2)

• Remove the rear panel (54) And the two proﬁ les (9-10).

• Fix the two plates (78) to the zinc-plated sides where three

holes are located (to be used according to the models).

for the VIP model (Illustr. 3-4)

• The left-hand plate must be ﬁ xed to the central and upper

holes, whilst the right-hand plate must be ﬁ xed to the central

and lower holes.

• Fit the ceramic tiles (57-58) on to the plates (78)

• Place 2 silicone-coated spacers (150) in the lower part betwe-

en the cast iron base and the lower, right-hand tile (58) (see

detail Y - Illustr. 4).

• For correct fastening of the upper right side ceramic tile and

the lower left side ceramic tile use the stop adjustment screws

located on the zinc-plated sides of the structure (Illustr. 5-6)

• Right-hand side (Illustr. 5): adjust the ﬁ xing screw abutted

against the upper right side ceramic tile (57).

• Left-hand side (Illustr. 6): remove the upper left ceramic tile

(57) and adjust the ﬁ xing screw abutted against the lower left

side ceramic tile (58).

• Replace the upper left ceramic tile (57).

for the BIG model (Illustr. 8-9)

• The left-hand plate must be fastened to the central and lower

hole, whilst the right-hand plate must be fastened to the central

and upper hole.

• Fit the ceramic tiles (41) on to the plates (78)

NOTE: Being made through a process of casting,the tiles may

differ slightly in height. To compensate for any height varia-

tions, silicone spacers may be inserted (150 - ﬁ g. 4-9) without

affecting the aesthetic appearance of the stove.

• Replace the proﬁ les (9-10) Replace the rear panel (54).

ASSEMBLING THE UPPER FRONT PANEL BIG/VIP

(ﬁ g. 10-11)

• Position the ceramic upper front panel (22) so that it rests

against the front panel support (23) positioned above the door.

• Use an Allen key to fasten the front panel in place using

the 2 supplied M6x25 screws (the door must be opened before

performing this operation).

NOTE: For correct assembly of the upper front panel (22), pla-

ce the bushing supplied between the same and the front panel

(23), as shown in detail “Z” in Illustr. 11.

ASSEMBLING THE LOWER FRONT PANEL BIG/VIP

(ﬁ g. 10-12)

• Use the supplied Allen key to loosen the screws that hold

the cast iron lower front grill (43) in place and remove it.

• Position the front panel (22) and use an Allen key to

fasten it in place using the 2 supplied M6x25 screws as indica-

ted in detail “X” (ﬁ g. 12).

ﬁ g. 7

ﬁ g. 5

ﬁ g. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Lux Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info