Bedienungsanleitung Edilkamin Pellkamin 10 (Seite 5 von 32) (Englisch)

810729

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

- 33 -

ENGLISH

g. 1

GENERAL INFORMATION

PRINCIPLE OF OPERATION

PELLKAMIN is an insert that uses pellets as fuel. Combustion

is electronically managed.

The combustion chamber is made with steel perimeter structure

covered, at the back, with a cast-iron panel and closed, at the

front, with a ceramic glass door (use the thermal glove pro-

vided when opening).

The fuel (pellets) is taken from the storage tank (A). A cochlea

(B) is enabled by a gear motor (C), which takes the fuel to the

combustion chamber (D).

The pellets are ignited by hot air produced by an electrical resi-

stance (E) and suctioned into the combustion chamber by

means of a centrifugal fan.

The smoke produced by combustion is extracted from the

hearth by means of this centrifugal fan and expelled from the

mouth located in the upper area of the insert (F).

Through the lower grille (G), the fans draw air from the room

that, routed through the cavity on the back of the combustion

chamber, is heated before returning to the room through the

upper grille (H).

Provide two aeration grilles (area larger than 100 cm2), the rst

one under the insert and the second positioned at least 50 cm

above the insert or anyway communicating with the internal

compartment where the insert is positioned, as indicated on

page 48.

The fuel tank (A) is situated to the rear of the insert.

The hopper can be lled in the following ways:

– through extraction of the insert, see page 42.

(TO BE CARRIED OUT ONLY WITH THE INSERT

TURNED OFF).

– using the pellet loading kit (optional), complete with loading

mouth to apply to the mantel, see page 43.

(THE INSTALLATION OF THE KIT ALLOWS PEL-

LETS TO BE LOADED IN THE HOPPER FROM THE

FRONT WITHOUT HAVING TO TURN OFF THE IN-

SERT).

– using the pellet front loading drawer kit (optional see page

46).

(INSTALLATION OF THE KIT MAKES IT POSSIBLE

TO LOAD THE PELLETS INTO THE HOPPER FROM

THE FRONT AND FROM THE SIDE WITHOUT HAV-

ING TO SHUT DOWN THE INSERT).

Fuel quantity, smoke extraction and combustion air supply

are all controlled by an electronic control board, which is

equipped with Leonardo software to achieve high combustion

ef ciency and low emissions.

All phases of operation can be managed via radio remote

control.

In case of breakage or loss of the radio remote control, switch-

ing on and off and setting the operating power can be done

through a 1,2-metre cable, complete with simplied on-button

to be placed near the insert by the installer (see page 53).

• Each time the insert is removed, a security system cuts off the

power supply. Should the insert be removed involuntarily du-

ring ignition, operation or while switching off (including while

blocked), the “Power failure” block phase will be launched

when the insert is reinserted. Wait for the block phase to end

before reactivating the insert.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Pellkamin 10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Pellkamin 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info