Bedienungsanleitung Edilkamin Story (Seite 45 von 209) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

810770

Zoom out

Zoom in

Vorherige Seite

1/209

Nächste Seite

- 45 -

ENGLISH

POSSIBLE TROUBLESHOOTING

In the event of problems the stove stops automatically and runs the shutdown process and the display shows text

regarding the motivation of the shutdown (see the various alarms below).

Never pull the plug during shutdown on account of malfunction.

Should it block, to restart the stove you will need to allow the turn-off procedure to take place (600 seconds with

audible signal), and then press the button 0/1 .

Do not turn the stove on again before checking the cause of the malfunction and CLEANING/ EMPTYING the crucible.

INDICATION OF POSSIBLE CAUSES OF MALFUNCTION AND INDICATIONS AND REMEDIES:

1) Signalling: Veriﬁ c./air ﬂ ow: (intervenes if the ﬂ ow sensor detects insufﬁ cient combustion ).

Problem: Turns off for lack of depression

Air ﬂ ow may be insufﬁ cient because the door is open, the door does not close properly (e.g. bad seal), there is an

air intake or smoke extraction problem, or the combustion chamber is clogged.

Actions: Check:

• door closure;

• combustion air intake duct (clean, paying attention to the ﬂ ow sensor components);

• clean the ﬂ ow sensor with dry air (like that used for PC keyboards);

• stove location: it must not be installed against a wall;

• combustion chamber position and cleanliness (clean regularly according to the type of pellet);

• smoke duct (clean);

• installation (if it does not comply with regulations or the smoke outlet has more than 2-3 bends);

If you suspect the sensor is malfunctioning, carry out cold tests. If the conditions are changed (for example by

opening the door) and the value does not change, there is a sensor problem.

N.B.: The no depression alarm may also occur during ignition, since the ﬂ ow sensor starts monitoring 90 seconds after

the ignition cycle begins.

2) Signalling: Veriﬁ c./extract.: (this trips if the smoke extraction speed sensor detects a fault)

Problem: Shutdown for smoke extraction speed fault detection

Actions: • Check smoke extractor function (devolution sensor connection) and board (DEALER).

• Check smoke channel for dirt

• Verify the electrical system and earthing system.

• Check eletronic circuit board (DEALER).

3) Signalling: Stop/Flame: (this trips if the thermocouple detects a smoke temperature lower than the value set, which it

interprets as the absence of ﬂ ames)

Problem: Turns off due to drop in smoke temperature

Actions: • lack of pellets

• too many pellets have suffocated the ﬂ ame, check pellet quality (DEALER)

• the maximum thermostat has intervened (rare, this only intervenes in the event of excessive smoke

temperature) (DEALER)

4) Signalling: Block_FI/NO Start: (intervenes if a ﬂ ame fails to appear within a maximum of 15 minutes, or if ignition

temperature is not reached).

Problem: Turns off due to incorrect smoke temperature during ignition

Distinguish either of the following cases:

Flame does NOT appear

Actions: • Check: - combustion chamber position and cleanliness;

• arrival of combustion air in the combustion chamber;

• if the heating element is working (DEALER);

• room temperature (if lower than 3°C use a ﬁ relighter) and damp.

Try to light with a ﬁ relighter (see page 38).

Flames appear, but AF appears on the display after Ar

Actions: • Check: (only by the Dealer)

• if the thermocouple is working (DEALER);

• start-up temperature setting in the parameters (DEALER).

• Repeat start up after having emptying the brazier.

5) Signalling: Black Out: (not a defect of the stove).

Problem: Turns off due to lack of electricity

Actions: • Check electricity connection and drops in voltage.

6) Signalling: Fault/RC: (intervenes if the thermo coupling has failed or is disconnected).

Problem: Turns off due to thermo coupling failed or disconnected

Actions: • Check connection of thermo coupling to board: check function in cold test (DEALER).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Story Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info