Bedienungsanleitung Edilkamin Tally 8 (Seite 42 von 48) (Englisch)

810812

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

Lighting a hot fireplace

When should wood be added? When the fuel is

almost completely consumed to embers. With the

glove supplied, slowly open (to avoid formation of

vortexes that can cause smoke to exit) the door. Add

the desired wood to the fireplace, locating it on the

existing embers (within the quality limits indicated in

the technical table).

Stove functioning changes with the chimney flue draft

and adjustment of the air valve in combustion.

Functioning with initial low draft

To extract air for combustion and discharge the

smoke, the fireplace needs a draft to be exerted on the

chimney flue.

If the draft is weak, initially light a “starter” fire using

small sized lighting material.

Once the correct draft is restored, you can add the fuel.

As with all the products, the wood stove heats and

cools during the various phases. This would lead to

normal dilation. Such dilation can cause slight settling

noise, which is not a reason for dispute.

The hot air reaches the premises with natural motion

(natural convection) without the help of a fan.The

retailer also offers an Air Diffuser kit with fans to

distribute the hot air in the premises.

NOTE FOR UK

Refuelling on to a low fire bed

If there is insufficient burning material in the firebed to

light a new fuel charge, excessive smoke emission can

occur. Refuelling must be carried out onto a sufficient

quantity of glowing embers and ash that the new fuel

charge will ignite in a reasonable period. If there are

too few embers in the fire bed, add suitable kindling to

prevent excessive smoke

Fuel overloading

The maximum amount of fuel specified in this manual

should not be exceeded, overloading can cause

excess smoke.

ISTRUCTIONS FOR USE

First switch on phases

• Ensure you have read and understood the content

of this manual

• Remove all the inflammable parts from the product

(manuals, labels, etc.). In particular remove any

labels from the glass. If they melt, they would

irreversibly damage the glass.

For initial switch on of the fireplace, always use the

smallest logs. Use larger wooden logs to raise the fire.

Always locate the wood deep in the fireplace, almost in

contact with the rear wall, so that even if they slide they

won’t come in contact with the glass.

There may be a slight smell of paint the first few times it

is ignited, however, this will disappear quickly.

Lighting a cold fireplace

1. Check the existing ash bed is not too high. If the

ash bed is too high, there is a danger of opening the

door of the fireplace to add wood and possible brazier

fragments fall out of the fireplace.

2. Position the adjustment lever of the valve in the “total

opening” position. The air for combustion will flow

intensely to the wood in the fireplace, to quickly reach

good combustion.

3. place the wood in the fireplace without excessively

squashing it in. Position a firelighter between the wood

logs and light. Never user materials such as petrol,

alcohol and similar to switch on.

4. At this point, close the door and monitor it for a few

minutes. If the fire should extinguish, slowly open the

door, re-position another firelighter between the logs

and light again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Tally 8 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Tally 8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info