Bedienungsanleitung Edilkamin Vyda H - EKleaner (Seite 13 von 52) (Englisch)

810913

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

WATER CIRCUIT INSTALLATION

PLUMBING

Vyda H and Kira H are provided with a closed expansion

tank.

The built-in expansion tank does NOT ensure proper

protection of the water in the entire system from thermal

expansion.

Therefore, installers should assess whether an

additional expansion tank is needed, depending on the

type of system.

ALL OTHER HYDRAULIC COMPONENTS MAY

BE INSTALLED WITHIN THE BOILER STOVE BY

PURCHASING A KIT FROM EDILKAMIN OR IF

PREPARED BY THE INSTALLER.

Plumbing depends on the type of system.

However, there are some “general rules”:

• The hydraulic system must operate at a pressure

between 1 and 1.5-2 bar at running temperature

(hot) in a closed vessel circuit.

• DO NOT install the boiler stove as a replacement in

a system with an open expansion tank.

• The presence of an accumulator (tank) is

recommended but not mandatory. Its advantage

is that it releases the boiler stove from “sudden”

requests from the system and can be integrated

with other heat sources. It reduces fuel

consumption and increases the efficiency of the

system. Edilkamin recommends an accumulator of

at least 20 l/kW.

• The return temperature of water to the boiler

stove must be higher than 50-55° C to prevent the

formation of condensation.

• An accumulator (tank) is needed to heat low-

temperature radiant panels and must be installed

according to the panel manufacturer's instructions.

• The material used in the circuit must be suitable to

withstand overheating.

• The installer must determine whether or not to use

conditioned products. In Italy, refer to UNI 8065

(Water treatment in heating systems for civil use).

• Direct plumbing to radiators prevents proper

operation, owing to the small diameter of their pipes.

Edilkamin offers four internal kits (optional)

PIPE KIT

it consists of delivery and return pipes if the other

hydraulic components are installed externally (pump,

etc.).

R KIT (specific for Vyda H and Kira H)

for installations without the production of instant

domestic hot water.

R2 KIT (specific for Vyda H and Kira H)

For installations without the production of instant

domestic hot water with system separator.

RW KIT (specific for Vyda H 22 and Kira H 22)

For installations with the production of instant domestic

hot water. Recommended for 22 kW models only.

PRESSURE GAUGE

Kira H and Vyda H are provided with an electronic

reading system for water pressure. Therefore, there is

no analogue pressure gauge. Water pressure is shown

on the display, on the bottom left (*) as indicated in

the figure below. Edilkamin proposes an analogue

pressure gauge as optional.

VENT

During normal operations the vent

is automatic. During installation, the

technician must check the functionality of

the automatic vent and assess whether a

manual vent needs to be installed.

INSTALLER

check that the swivel nut (G) on

the two output pipes of the boiler

stove are closed

The product, without any kit, comes as shown in the

figure below.

(*)

Real size templates are available for technicians.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Vyda H - EKleaner Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Vyda H - EKleaner

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info