Bedienungsanleitung Edilkamin Windo 70 (Seite 32 von 36) (Englisch)

32

ENGLISH

INSTRUCTIONS FOR USE

Lighting a cold fireplace

1. Check the existing ash bed is not too high. If the

ash bed is too high, there is a danger of opening the

door of the fireplace to add wood and possible brazier

fragments fall out of the fireplace.

2. Position the adjustment lever of the valve in the “total

opening” position . The air for combustion will flow

intensely to the wood in the fireplace, to quickly reach

good combustion.

3. place the wood in the fireplace without excessively

squashing it in. Position a firelighter between the wood

logs and light. Never user materials such as petrol,

alcohol and similar to switch on.

4. At this point, close the door and monitor it for a few

minutes. If the fire should extinguish, slowly open the

door, re-position another firelighter between the logs

and light again.

Lighting a hot fireplace

When should wood be added? When the fuel is almost

completely consumed to embers. With the glove,

slowly open (to avoid formation of vortexes that can

cause smoke to exit) the door. Add the desired wood to

the fireplace, locating it on the existing embers (within

the quality limits indicated in the technical table).

Product functioning changes with the chimney flue

draft and adjustment of the air valve in combustion.

Functioning with initial low draft

To extract air for combustion and discharge the

smoke, the fireplace needs a draft to be exerted on the

chimney flue.

If the draft is weak, initially light a “starter” fire using

small sized lighting material.

Once the correct draft is restored, you can add the fuel.

FUEL

The product was designed to burn wooden logs or

sawdust briquettes.

Use dry wood logs (max. humidity 20%)Use logs The

use of damp wood would cause the product and the

flue to get dirty, the risk of smoke and a lower yield

than that declared.Each type of wood has different

characteristics that also influence combustion yield.

The data outlined on this manual are with wood used

during certification.

In general wood can have a heat of combustion up to

4.5 kWh/kg while cut fresh it has heat of combustion

around 2 kWh/kg

In general, beech or elm is recommended, or however

class A1 wood according to UNI EN ISO 17225-5

Attention to prolonged use of wood with aromatic oils

(e.g. eucalyptus). Cast iron parts can deteriorate

Use the recommended quantities of wood:

Overloading causes overheating, resulting in damage:

• possible deformation of the inner parts;

• possible irreversible changes to the colour of the

paint on the metal parts for which Edilkamin or the

retailer cannot be held liable.

To respect the environment and safety, do NOT burn,

among other things: plastic, varnished wood, coal and

bark waste. Do not use the product as an incinerator.

Use of these fuels also nullifies the guarantee.

TO OBTAIN THE RATED POWER, FOLLOW

THE INDICATIONS ON THE TECHNICAL

CHARACTERISTICS PAGES

First switch on phases

• Ensure you have read and understood the content

of this manual

•

Remove all the inflammable parts from the product

(manuals, labels, etc.). In particular remove any

labels from the glass. If they melt, they would

irreversibly damage the glass.

For initial switch on of the fireplace, always use the

smallest logs. Use larger wooden logs to raise the fire.

Place the wood on the combustion grille.

NOTE

Always locate the wood deep in the fireplace, almost in

contact with the rear wall, so that even if they slide they

won’t come in contact with the glass.

Employer toujours le gant en dotation

pour les parties chaudes.

Avoid direct contact with hot parts.

USE ONLY WITH REFRACTORIES

INSTALLED

Edilkamin Windo 70 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Windo 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info