Bedienungsanleitung Edy EDTK5507 (Seite 26 von 30) (Deutsch, Englisch, Holländisch, Französisch)

726249

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

efore you start

• This appliance has a heavy weight. Be careful when transporting it.

• Do not lift the appliance b

y the pipes or the door when moving.

• This appliance must stand vertically on a flat, even surface, to level the appliance use the

leveling feet by turning them until the appliance is as level as possible.

• Do not install onto carp

eted surfaces as this prevent adequate ventilation.

• Install the appliance in a w

ell ventilated room. The appliance should not be placed near to

any heat sources (cookers, heaters etc.) or in any unheated rooms (garages, outhouses etc.) as

the ambient temperature affects the performance of the appliance.

• P

arts that become hot must never be exposed. The back of the appliance must therefore be

placed against the wall not forgetting the customary distance for ventilation. Allow 300 mm

clearance at the rear of the appliance and on each side of the appliance and over the top to

ensure proper ventilation.

• Do not e

xpose the appliance to damp conditions, open air or rain.

• After y

ou remove all of the packaging materials, clean the inside of your refrigerator before

using it.

• Should the appliance b

ecome damaged, contact the service center and do not use the

appliance until y

ou are instructed to do so by a service engineer.

Getting star

ted

Once you have installed your appliance in an appropriate location, follow the start up procedure

below:

• Before you plug in the appliance, clean thoroughly the inside and all accessories.

• Leav

e the appliance to stand for 2 - 3 hours to allow the refrigerant to settle following instal-

lation and cleaning.

• If the appliance has been transported horizontally, it must be left to stand vertically for 12

hours before installation.

• Once dry, plug the appliance into the socket. Make sure the voltage of this appliance is in

accordance with the voltage of your energy grid.

• Turn the thermostat to the required setting.

• When using the freezer for the ﬁrst time or after defrosting, set the thermostat knob to the

maximum position for at least 2 hours before introducing food to be stored, and then adjust it

to the normal position.

Temperature control

The temperature selector knob is located on the right hand side wall of the refrigerator interior.

The temperature of the chamber is adjusted through the thermostat knob. The numbers 1, 2, 3,

4, 5, 6, do not mean a speciﬁc temperature, the lower the number is, the higher the temperature

inside will be and vice versa.

During high ambient temperatures e.g. on hot summer days, it may be necessary to set the

thermostat to the coolest setting (position”Max”).This may cause the compressor running con-

tinuously in order to maintain a low temperature in the cabinet.

The ﬁrst time you install your refrigerator, set the thermostat knob at “Med”. Give your refrigerator

time to cool down completely before adding food. Wait 24 hours before adding food.

The thermostat knob controls the temperature. When the thermostat control knob is set to OFF,

the refrigerator will not be running.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edy EDTK5507 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info