Bedienungsanleitung Einhell BT-AC 190-6 OF (Seite 15 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Schwedisch, Finnisch)

606101

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

- 15 -

4. Technical data

Power supply: .................................... 230 ~ 50 Hz

Motor rating in kW: .......................................... 1.1

Operating mode .......................... S3 25% 10 min

Compressor speed in rpm: ........................... 3550

Operating pressure in bar: ................................. 8

Pressure vessel volume in litre: .......................... 6

Theoretical intake rate in l/min.: ...................... 185

Sound power level L

in dB: ............................ 97

uncertainty .............................................2 dB

Sound pressure level L

in dB: ........................ 75

uncertainty .............................................2 dB

Protection type: ............................................ IP 20

Machine weight in kg: ......................................... 9

Noise

The noise emission values were measured in ac-

cordance with EN ISO 3744.

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

•

Examine the machine for signs of transit da-

mage. Report any damage immediately to the

company which delivered the compressor.

•

The compressor should be set up near the

working consumer.

•

Avoid long air lines and long supply lines (ex-

tensions).

•

Make sure the intake air is dry and dust-free.

•

Do not set up the compressor in damp or wet

rooms.

•

The compressor may only be used in suitable

rooms (with good ventilation and an ambient

temperature from +5°C to +40°C). There must

be no dust, acids, vapors, explosive gases or

inflammable gases in the room.

•

The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor

in areas where work is conducted with spray-

ed water.

6. Assembly and starting

 Important!

You must fully assemble the appliance before

using it for the ﬁ rst time.

6.1 Voltage

Before you use the machine, make sure that the

mains voltage complies with the speciﬁ cations on

the rating plate. Long supply cables, extensions,

cable reels etc. cause a drop in voltage and can

impede motor start-up. In the case of low tempe-

ratures below +5°C, motor start-up is jeopardized

as a result of stiﬀ ness.

6.2 On/Oﬀ switch (8)

To switch on the equipment set the On/Oﬀ switch

(8) to position 1.

Move the On/Oﬀ switch (8) to position 0 to switch

oﬀ the equipment.

6.3 Adjusting the pressure: (Fig. 1)

•

You can adjust the pressure on the pressure

gauge (6) using the pressure regulator (7).

•

The set pressure can be taken from the quick-

lock coupling (5).

6.4 Setting the pressure switch

The pressure switch is set at the factory.

Switch-on pressure 6 bar

Switch-oﬀ pressure 8 bar

7. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel

to avoid danger.

Anl_BT_AC_190_6_OF_SPK7.indb 15Anl_BT_AC_190_6_OF_SPK7.indb 15 19.04.12 08:2819.04.12 08:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell BT-AC 190-6 OF Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info