Bedienungsanleitung Einhell BT-RO 1100 E KIT (Seite 22 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

606718

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 22 -

material. Use a special vacuum cleaner if you

are handling harmful materials.

•

Secure the extraction port (1) to the routing

shoe (2) using the two countersunk screws

(f).

•

The extraction port can be connected to ext-

ractor units (vacuum cleaners) with a suction

hose.

•

The internal diameter of the suction port is 35

mm. Now fit a suction hose of the appropriate

size to the suction port.

5.2 Safety guard port assembly

(Fig. 3/Item 24)

Fit the safety guard (24) as shown in Fig. 3.

5.3 Parallel stop assembly (Fig. 4/Item 21)

•

Push the guide shafts (a) of the parallel stop

(21) into the holes (b) on the routing shoe (2).

•

Set the parallel stop (21) to the required di-

mension and secure it in place with the wing

screws (3).

5.4 Fitting the compass point (Fig. 5)

•

You can route circular areas using the com-

pass point (13) and the mounting to go with it.

•

Clamp the compass point (13) to the end of

one of the guide rods (a). Push the guide rod

(a) into a hole (b) on the routing shoe (2). Se-

cure the guide rod (a) on the routing shoe (2)

using the securing screws (3).

•

Set the required radius between the compass

point (13) and cutter.

•

Position the compass point (13) in the center

of the circle you wish to route. If necessary

undo the wing screw (c) on the compass

point (13) and extend/shorten the part of the

compass point (13) that points downwards.

5.5 Guide sleeve assembly (Fig. 6-7/Item 20)

•

Secure the guide sleeve (20) to the routing

shoe (2) using the two countersunk screws

(f).

•

The guide sleeve (20) is guided along the

template (c) using the guide ring (b).

•

The workpiece (d) must be larger by the diffe-

rence of “external edge of guide ring” and “ex-

ternal edge of router” (e) to obtain a precise

copy.

5.6 Fitting / Removing the cutting tool

(Fig. 8-11)

 Important. Pull out the power plug ﬁ rst.

 Important. After working with the router,

the cutting tool will remain very hot for a rela-

tively long time.

 Important. Cutters are very sharp. Wear

protective gloves at all times when handling

cutting tools.

•

Cutters with a shaft diameter of 6 mm and 8

mm may be fitted to this router. Most cutters

are available in both sizes.

•

You can use cutters made of the following

materials:

- HSS - suitable for cutting softwood

- TCT - suitable for cutting hardwood, particle

board and plastic.

•

Select the appropriate cutting tool for the job

in hand.

•

When using the cutters for the first time: Re-

move the plastic packaging from the cutter

heads.

•

Clean the nut, clamp and shaft of the cutter

before fitting it.

•

Press the spindle lock (12) and allow the

spindle to engage by turning it at the same

time.

•

Undo the clamp nut (10) using the open-

ended spanner (22).

•

If necessary take the cutter you wish to remo-

ve out of the clamp (23).

•

Select the appropriate cutting tool for the job

in hand.

•

Select the appropriate clamp for the cutter

(23).

•

Now fit the clamp (23) and nut (10) into the

cutting spindle.

•

Guide the cutter shaft into the clamp.

•

Press and hold the spindle lock (12).

•

Tighten the clamp nut (10) using the open-

ended spanner (22).

•

The cutter must be inserted at least 20 mm

into the clamp (23).

•

Before you start the electric router, check to

ensure that the cutting tool is secure and runs

smoothly.

 Important. Remove the setting and assem-

bly tools before starting the machine

Anl_BT_RO_1100_E_KIT_SPK1.indb 22Anl_BT_RO_1100_E_KIT_SPK1.indb 22 26.06.12 17:1726.06.12 17:17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell BT-RO 1100 E KIT Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell BT-RO 1100 E KIT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info