Bedienungsanleitung Einhell GC-ES 1231 (Seite 17 von 80) (Englisch, Dänisch, Schwedisch, Norwegisch)

605767

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

- 17 -

•

Using the cable clips supplied (Fig. 7), attach

the power cable to the tubes of the push bars

so that it is possible to open and shut the

ejector flap (Fig. 8/Item 10).

Please ensure that the ejector ﬂ ap can be opened

and closed easily!

Adjusting the scariﬁ er depth (see Fig. 9)

The scariﬁ er depth is adjusted at both front

wheels via the adjustment mechanism. For this,

pull out the adjusting screw and turn the wheel to

the left or right into one of the available positions

(0/I/II/III).

The scariﬁ er depth must always be identically set

on both sides!

0 = drive/transport position

I = scariﬁ er depth 3 mm

II = scariﬁ er depth 7 mm

III = scariﬁ er depth 9 mm

Electrical connection

The equipment can be connected to any normal

socket with 230V AC. It is only acceptable to con-

nect it to a shockproof socket with a 16A circuit

breaker. Furthermore, a residual-current-operated

protective device with max. 30 mA should be con-

nected upstream.

Power cable

Please only use power cables that are not dama-

ged. The total length of the power cable should

not exceed 50 meters; going beyond this distance

will reduce the power output of the electric motor.

The power cable must have a cross-section of 3 x

1.5 mm2. The insulating sheath of scariﬁ er power

cables is frequently damaged.

Some of the causes for this are:

•

Cracking from running over the cable

•

Pinching when the power cable is dragging

under doors and pulled through windows

•

Cracking due to old age of the insulation

•

Kinking by improperly fastening or guiding the

power cable

The power cables must, at the very minimum, be

of type HO5RN-F and 3-stranded. The cable type

must be printed somewhere on the power cable.

Only purchase power cables that are marked as

such! Plugs and socket couplers for the power

cables must be made from rubber and be splash-

proof. There is a limit to how long power cables

can be. Longer power cables require larger con-

ductor cross-sections. Power cables and connec-

ting lines must be regularly checked for damage.

Ensure that the lines are de-energized before

checking them. Completely unwind the power

cable. Also check power cable entry points, plugs

and socket couplers for kinks.

6. Operation

Connect the machine’s power supply cable to the

plug (Fig. 10/Item 1) and secure the power cable

with the stress-relief clip (Fig 10/Item 2).

To prevent accidental start-up of the equipment,

the push-bar (Fig. 11 / Item 5) is equipped with

a safety lock-oﬀ (Fig. 11 / Item 2) which must be

pressed before the lever switch (Fig. 11 / Item 1)

can be pressed. If the lever switch is released, the

equipment switches oﬀ .

Repeat this process several times so that you are

sure that the machine functions properly. Before

you perform any repair or maintenance work on

the machine, ensure that the cutting unit is not ro-

tating and that the power supply is disconnected.

Important! Never open the ejector ﬂ ap when the

motor is running. A rotating cutting unit can cause

injuries.

Always fasten the ejector ﬂ ap carefully. The ﬂ ap

ﬂ ips back to the “Closed” position by the tension

springs!

Always ensure that a safe distance (provided

by the long handles) is maintained between the

user and the housing. Be especially careful when

scarifying and changing direction on slopes and

inclines. Maintain a solid footing and wear sturdy,

non-slip footwear and long trousers. Always sca-

rify along the incline (not up and down).

For safety reasons, the scariﬁ er may not be used

to scarify inclines whose gradient exceeds 15

degrees.

Use special caution when backing up and pulling

the scariﬁ er (tripping hazard)!

Tips for proper working

It is recommended that you overlap scarifying

paths a little.

Try to scarify in straight lines for a nice, clean look.

Insodoing, the aeration swaths should always

overlap each other by a few centimeters in order

to avoid bare strips.

Anl_GC_ES_1231_SPK1.indb 17Anl_GC_ES_1231_SPK1.indb 17 28.08.14 11:1628.08.14 11:16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GC-ES 1231 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell GC-ES 1231

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info