Bedienungsanleitung Einhell GE-CM 33 Li (Seite 23 von 198) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

724270

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

- 23 -

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

5. Before starting the equipment

The lawn mower is delivered partly assembled.

The push bar and the grass basket must be as-

sembled before using the lawn mower. Follow the

instructions step by step and refer to the pictures

when assembling.

Mounting the push bar (Fig. 3 to 5)

Start by fastening the lower push bars for the left-

hand side (Fig. 3/Item 10) and the right-hand side

(Fig. 3/Item 11) to the mower housing using the

fastening screws (Fig. 3/Item 12). The upper push

bar then has to be slid onto the lower push bars

and fastened with screws (Fig. 4/Item 13). There

are 2 diﬀ erent holes on each of the lower push

bars for this, to enable the height of the push bar

to be adjusted to the height of the user. Then fas-

ten the power cable to the push bar with the cable

clips (Fig. 5/Item 14).

Mounting the catch basket (see Fig. 6)

Before you ﬁ t the catch basket you must ensure

that the motor is switched oﬀ and the blade is not

rotating. Lift the ejector ﬂ ap (Fig. 6/Item 6) with

one hand. With the other hand, hold the catch

basket by the handle and hook it in from above

(Fig. 6).

Filling level indicator of the grass collector

The grass box is equipped with a ﬁ lling level in-

dicator (Fig. 1/Item 15). which is opened by the

airﬂ ow that the lawn mower generates during ope-

ration. If the ﬂ ap closes during mowing, the grass

collecting device is full and must be emptied. To

ensure the proper functioning of the ﬁ lling level

indicator, the holes under the ﬂ ap must always be

kept clean and passable.

Adjusting the cutting height

Caution!

Adjust the cutting height only when the machine

has been switched oﬀ and the safety plug has

been pulled out.

Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged. To prevent any imbalance, replace

blunt and/or damaged blades. To carry out this

check, ﬁ rst switch oﬀ the motor and pull out the

safety plug.

The cutting height is adjusted as follows (see Fig.

7):

1. Push the lever (5) downwards.

2. Set the lever (5) to the desired cutting height.

3. Release the lever (5) and check that it is se-

curely seated in the lock.

Reading oﬀ the cutting height

The cutting height can be set between 25-65 mm

in 5 intervals, and can be read oﬀ on the scale.

Charging the battery (Fig. 8)

1. Take the battery pack out of the equipment.

Do this by pressing the side pushlock buttons.

2. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Insert the power plug of the charger

(9) into the socket outlet. The green LED will

then begin to ﬂ ash.

3. Insert the battery pack (8) into the battery

charger (9).

4. In the section entitled „Charger indicator“ you

will ﬁ nd a table with an explanation of the LED

indicator on the charger.

The battery pack can become a little warm during

the charging. This is normal.

If the battery pack fails to charge, check:

•

whether there is voltage at the socket outlet

•

whether there is good contact at the charging

contacts

If the battery pack still fails to charge, send

•

the charging unit

•

and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly.

You must recharge the battery pack when you

notice that the performance of the device drops.

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

Installing the battery (Fig. 9-10)

Open the battery cover. This is done by pulling

the snap fastener (Item A) as shown in Fig. 9 and

swinging up the cover. Then insert the two batte-

ries in the mounts as shown in Fig. 10.

Anl_GE_CM_33_Li_Kit_Solo_SPK9.indb 23Anl_GE_CM_33_Li_Kit_Solo_SPK9.indb 23 09.04.2019 09:32:3309.04.2019 09:32:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-CM 33 Li Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell GE-CM 33 Li

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info