Bedienungsanleitung Einhell GE-DP 7330 LL ECO (Seite 21 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605858

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

- 21 -

Manual operation:

Mount the ﬂ oating switch as illustrated in Fig. 1.

The equipment will then run continuously. To pre-

vent dry running, this operating mode is allowed

only under supervision. The equipment must be

switched oﬀ (pull out the power plug) as soon as

no more water is emitted from the discharge line.

Dirty water mode (Fig. 4/5):

•

Turn the equipment counter-clockwise up as

far as the stop (Fig. 4/5).

Shallow suction mode (Fig. 5):

•

Turn the equipment clockwise down as far as

the stop (Fig. 5).

•

In shallow suction mode, water can be su-

cked up down to a level of 1 mm.

•

Only clean water can be sucked up in shallow

suction mode.

Please note:

For the equipment to suck up water in shallow

suction mode there must be a minimum depth of

10 mm of water.

7. Replacing the power cable

Danger!

If the power cable for this equip-

ment is damaged, it must be

replaced by the manufacturer or

its after-sales service or similarly

trained personnel to avoid dan-

ger.

8. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

8.2 Cleaning the intake cage and pump

housing (Fig. 5/6/7/8):

1. Screw out the three screws (Fig. 6/Item B)

counter-clockwise.

2. Turn the equipment up as far as the stop (Fig.

5). Note the position of the lug (Fig. 5/Item A)

and remove the intake cage (Fig.7/Item 4).

3. Clean the intake cage (Fig. 7/Item 4) and the

pump impeller housing (Fig.7/Item C) with

clean water.

4. Assemble in reverse order.

5. When assembled, the lug must be in the cor-

rect position (Fig. 8/Item A).

8.3 Maintenance

There are no parts inside the equipment which

require additional maintenance.

8.4 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

•

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

Anl_GE_DP_7330LL_5220LL_SPK7.indb 21Anl_GE_DP_7330LL_5220LL_SPK7.indb 21 15.10.14 10:0715.10.14 10:07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-DP 7330 LL ECO Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info