Bedienungsanleitung Einhell GH-BC 30 AS (Seite 21 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605959

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

- 21 -

4. Technical data

Engine type .........................................................

........2-stroke engine, air-cooled, chrome cylinder

Engine power (max.) ...................0.8 kW (1.1 HP)

Displacement ........................................30.3 ccm

Idle speed of engine .................3,000 ± 200 min

-1

Max. engine speed..............................8,500 min

-1

Max. torque

Scythe: ...............................................6,375 min

-1

Trimmer: .............................................5,550 min

-1

Ignition .................................................Electronic

Drive ........................................Centrifugal clutch

Weight (with empty tank) ............................6.7 kg

Cutting line diameter (HYP, PA Ø 410) ........41 cm

Cutting circle diameter of blade

(HYP, 65 Mn Ø 230-4T) ...............................23 cm

Cutting line length ......................................... 8 m

Cutting line diameter: ................................. 2 mm

Tank capacity ................................................0.8 l

Spark plug ............................... Champion RCJ6Y

Danger!

Sound and vibration

Sound and vibration values were measured in

accordance with EN ISO 11806-1; EN ISO 22868;

EN ISO 22867.

sound pressure level ..................... 93.2 dB(A)

uncertainty ..........................................1.5 dB

sound power level ........................ 110 dB(A)

uncertainty ..........................................1,5 dB

Wear ear-muﬀ s.

The impact of noise can cause damage to hea-

ring.

Functions

Vibration emission value a

= 7 m/s

K uncertainty = 1.5 m/s

Keep the noise emissions and vibrations to a

minimum.

•

Only use appliances which are in perfect wor-

king order.

•

Service and clean the appliance regularly.

•

Adapt your working style to suit the appliance.

•

Do not overload the appliance.

•

Have the appliance serviced whenever ne-

cessary.

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

5. Assembly

5.1.1 Fitting the steady grip

Install the steady grip as shown in Figures 3a-3c.

Do not tighten the screws until you have set the

perfect working position with the carrying strap.

The steady grip should be aligned as shown in

Figure 1. To dismantle, proceed in reverse order.

5.1.2 Fitting the long handle (Fig. 4a-4c)

Pass the handle screw (32) through the washer

(34) and into the connecting piece of the long

handle (1) (Fig. 4b). Secure the handle screw loo-

sely with the nut (33).

Now press the locking lever (A) and push the long

handle (Fig. 4a/Item 2) carefully into the connec-

ting piece for the long handle. While doing so,

ensure that the drive shafts on the inside of the

long handle slide into each other (turn the spool

head gently, if required). The lug of the locking

lever (A) must latch into the hole (B). Now tighten

the handle screw as shown in Figure 4c. After this

initial assembly, you will only have to loosen the

handle screw and activate the lever to dismantle

the long handle.

5.1.3 Fitting the blade guard hood

Important: The cutting blade guard hood must be

ﬁ tted if you wish to work with the cutting blade.

The guard hood for the cutting blade must be ins-

talled as shown in Figures 5a – 5c.

5.1.4 Fitting/Replacing the cutting blade

The ﬁ tting of the cutting blade is shown in Figures

6a – 6g. To dismantle, proceed in reverse order.

•

Fit the carrier plate (22) onto the spline shaft

(Fig. 6b)

•

Securely fit the cutting blade (18) on the co-

ver ring (Fig. 6c)

•

Place the pressure plate (23) over the thread

of the spline shaft (Fig. 6d).

•

Plug on the cover of the pressure plate (24)

(Fig. 6e).

•

Look for the hole in the carrier plate, line up

with the notch underneath, lock with the sup-

plied Allen key (29), and tighten the nut (25)

(Fig. 6f/6g). Important: Left-hand thread

Anl_GH_BC_30_AS_SPK7.indb 21Anl_GH_BC_30_AS_SPK7.indb 21 16.06.14 11:4216.06.14 11:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GH-BC 30 AS Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info