Bedienungsanleitung Einhell TC-AC 190-24 (Seite 19 von 100) (Englisch, Dänisch, Schwedisch, Norwegisch)

606092

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

- 19 -

8.4 Check the oil level at regular intervals

Place the compressor on a level and straight sur-

face. The oil level must be between the two marks

MAX and MIN on the oil oil level window (Fig. 10).

Changing the oil: Recommended hydraulic oil:

SAE 5W/40 or an alternative of the same quality.

It should be reﬁ lled for the ﬁ rst time after 10 hours

of operation. Thereafter the oil should be drained

and reﬁ lled after every 100 hours in service.

8.5 Changing the oil

Switch oﬀ the engine and pull the mains plug out

of the socket. After releasing any air pressure you

can unscrew the oil drainage screw (15) from the

compressor pump. To prevent the oil from running

out in an uncontrolled manner, hold a small metal

chute under the opening and collect the oil in a

vessel. If the oil does not drain out completely, we

recommend tilting the compressor slightly.

Dispose of the old oil at a drop-oﬀ point for

old oil.

When the oil has drained out, re-ﬁ t the oil draina-

ge screw (15). Fill new oil through the oil ﬁ ller ope-

ning (13) until it comes up to the required level.

Then replace the oil sealing plug (14).

8.6 Cleaning the intake ﬁ lter (1)

The intake ﬁ lter prevents dust and dirt being

drawn in. It is essential to clean this ﬁ lter after at

least every 300 hours in operation. A clogged

intake ﬁ lter will decrease the compressor‘s per-

formance dramatically. Undo the screw on the

air ﬁ lter so that the halves of the air ﬁ lter housing

can be opened. Use compressed air at low pres-

sure (approx. 3 bar) to blow out all the parts of

the ﬁ lter and then assemble the ﬁ lter in reverse

order. When cleaning, take adequate precautions

against dust (e.g. use a suitable face mask).

8.7 Storage

 Warning!

Pull the mains plug out of the socket and ventilate

the appliance and all connected pneumatic tools.

Switch oﬀ the compressor and make sure that it is

secured in such a way that it cannot be started up

again by any unauthorized person.

Important!

Store the compressor only in a dry location.

Always store upright, never tilted!

8.8 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

•

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

9. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled. The equipment and its accessories are

made of various types of material, such as metal

and plastic. Never place defective equipment in

your household refuse. The equipment should

be taken to a suitable collection center for proper

disposal. If you do not know the whereabouts of

such a collection point, you should ask in your

local council oﬃ ces.

Anl_TC_AC_190_24_SPK1.indb 19Anl_TC_AC_190_24_SPK1.indb 19 06.08.14 14:4106.08.14 14:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TC-AC 190-24 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell TC-AC 190-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info