Bedienungsanleitung Einhell TE-CD 18-2 i (Seite 21 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Finnisch)

606110

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

- 21 -

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/Oﬀ switch is for

setting the direction of rotation of the cordless

screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to

the gearing, the direction of rotation must only be

changed when the screwdriver is at a standstill.

When the slide switch is in the middle position,

the On/Oﬀ switch is blocked.

6.5 On/Oﬀ switch (Fig. 5 / Item 4)

Inﬁ nitely variable speed control is possible with

the On/Oﬀ switch. The further you press the

switch, the higher the speed of the battery-powe-

red drill/screwdriver.

6.6 Changing over from 1st gear to 2nd gear

(Fig. 6 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change

over gears when the tool has stopped.

6.7 LED display for clockwise/counter-clock-

wise operation (Figure 6/Item 11)

The LED display for counter-clockwise/clockwise

(11) indicates the position of the changeover

switch (3).

Green LED (11a) is lit: clockwise

Red LED (11b) is lit: counter-clockwise

6.8 Battery capacity indicator (Fig. 7 – Item 2)

Press the battery capacity indicator switch (a).

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED is lit:

The battery is empty, recharge the battery.

6.9 LED lamp (Fig. 7 / Item 10)

The LED lamp (10) can be used in poor lighting

conditions to illuminate the area where you want

to drill or screw. The LED lamp (10) will be lit

automatically as soon as you press the ON/OFF

switch (4).

6.10 Changing the tool (Fig. 8)

Caution! Set the changeover switch (3) to its

center position whenever you carry out any work

(for example changing the tool, maintenance

work, etc.) on the cordless hammer drill/screwdri-

ver.

•

The cordless screwdriver is fitted with a

quick-action chuck (9) with an automatic

spindle stop.

•

Open the chuck (9). The chuck opening (a)

must be large enough to hold the tool (drill bit

or screwdriver bit).

•

Select the suitable tool. Push the tool as far

as possible into the chuck opening (a).

•

Tighten the chuck (9) and then check that the

tool is secure.

6.11 Screwdriving

We recommend using self-centering screws (e.g.

Torx screws, recessed head screws) designed for

reliable working. Be sure to use a bit that matches

the screw in shape and size. Set the torque, as

described elsewhere in these operating instruc-

tions, to suit the size of screw.

6.12 Fitting the additional handle

(Fig. 9/Item 12)

The additional handle (12) enables you to achieve

better stability whilst using the hammer drill. Do

not use the tool without the additional handle.

The additional handle (12) is secured to the ham-

mer drill by a clamp. During the handle clockwise

tightens this clamp. Turning it anti-clockwise will

release the clamp.

•

The supplied additional handle (12) must

first be fitted. To do this, the clamp must be

opened by turning the handle until it is wide

enough for the additional handle to be slid

over the chuck (9) and on to the hammer drill.

•

After you have positioned the additional

handle (12), turn it to the most comfortable

working position for you.

•

Now turn the handle in the opposite direction

again until the additional handle is secure.

•

The additional handle (12) is suitable for both

left-handed and right-handed users.

Anl_TE_CD_18_2_i_SPK7.indb 21Anl_TE_CD_18_2_i_SPK7.indb 21 17.12.13 10:1517.12.13 10:15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TE-CD 18-2 i Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info