Bedienungsanleitung Einhell TE-CS 165 (Seite 22 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

606722

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 22 -

on the front of the saw foot.

•

You can now adjust the cutting angle to

around 45°. Keep an eye on the cutting angle

scale (9) as you do so.

•

Refasten the locking lever for miter setting (7).

Check the handle is securely fastened.

5.3 Precision adjustment of the miter stop to

0° or 90° (Figure 6/7)

With a 90° angle stop you can adjust the angle

setting to 0° or 90°.

To do so, undo the locking screw for the miter

stop (7) and the counternut (b) on the adjustment

screw (a). (See Figure 6)

Turn the hand-held circular saw upside down and

place the angle stop (c) between soleplate (6)

and saw blade (12). (See Figure 7)

Now set the adjustment screw (a) until the angle

between the soleplate (6) and saw blade (12)

equals 90°.

Retighten the counternut (b) and the locking

screw for the miter stop (7).

5.4 Extraction of dust and chips (Figure 1b)

•

Connect a suitable vacuum cleaner to the

provided chip extractor connector (14) of your

circular saw (vacuum cleaner not included).

This will provide excellent dust extraction on

the workpiece. The benefits are that you will

protect both the equipment and your own

health. Your work area will also be cleaner

and safer.

•

Dust created when working may be dange-

rous. Refer to the section entitled “Safety inst-

ructions”.

•

Important! The vacuum cleaner you use for

the extraction work must be suitable for the

workpiece material.

•

Check that all the parts are properly connec-

ted.

5.5 Parallel stop (Figure 8/9)

•

The parallel stop (16) enables you to saw par-

allel lines.

•

Loosen the locking screw for the parallel stop

(8) on the saw foot (6).

•

To assemble, slide the parallel stop (16) into

the guide (a) on the saw foot (6) (see Figure

•

Set the required spacing and then tighten the

locking screw (8) again.

•

Using the parallel stop: Position the parallel

stop (16) flat on the edge of the workpiece

and start the cut.

 Important! Carry out a trial cut in a piece

of waste wood

5.6 Line guide (Fig. 10)

Using the line guide (15) you can carry out exact

cuts following cutting lines marked on the work-

piece.

Use the mark (a) for the 0° or 90°angle setting.

For information on the angle setting see 5.2

 Important! Carry out a trial cut in a piece

of waste wood

6. Operation

6.1 Working with the hand-held circular saw

•

Always hold the circular saw firmly.

•

The swing guard hood (19) is pushed back

automatically by the workpiece.

•

Do not use force!

•

Push forwards gently and evenly with the

circular saw.

•

The waste piece should be on the right-hand

side of the circular saw so that the wide

section of the support bench supports its full

area.

•

If you are sawing down a line that has been

drawn, guide the circular saw along the corre-

sponding notch.

•

Clamp small pieces of wood securely before

sawing them. Never hold them with your

hand.

•

Always follow the safety instructions. Wear

safety goggles.

•

Do not use defective saw blades or blades

that are cracked or broken.

•

Do not use any flanges / flange nuts whose

bore hole is larger or smaller than those in the

saw blade.

•

The saw blade must not be decelerated by

hand or by applying lateral pressure to the

blade.

•

The swing guard hood must not jam and must

return to its initial position after the operation

has been completed.

•

Before you use the circular saw, check the

function of the swing guard hood with the

mains plug disconnected.

•

Before you use the machine, ensure that the

safety equipment such as the swing guard

hood, flanges and adjustment devices are in

working order and are correctly adjusted and

secure.

Anl_TE_CS_165_SPK1.indb 22Anl_TE_CS_165_SPK1.indb 22 01.07.14 15:1701.07.14 15:17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TE-CS 165 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell TE-CS 165

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info