Bedienungsanleitung Einhell TE-ID 1050-1 CE (Seite 17 von 108) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

606215

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

- 17 -

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Always pull the power plug before making adjust-

ments to the equipment.

5.1. Fitting the additional handle (Fig. 2-3/

Item 8)

The additional handle (8) enables you to achieve

better stability whilst using the hammer drill. Do

not use the tool without the additional handle.

The additional handle (8) is secured to the ham-

mer drill by a clamp. During the handle clockwise

tightens this clamp. Turning it anti-clockwise will

release the clamp.

•

The supplied additional handle (8) must

first be fitted. To do this, the clamp must be

opened by turning the handle until it is wide

enough for the additional handle to be slid

over the chuck (1) and on to the hammer drill.

•

After you have positioned the additional

handle (8), turn it to the most comfortable

working position for you.

•

Now turn the handle in the opposite direction

again until the additional handle is secure.

•

The additional handle (8) is suitable for both

left-handed and right-handed users.

5.2 Fitting and adjusting the depth stop

(Fig. 4/Item 2)

•

Undo the thumb screw (a) on the additional

handle (8) and insert the depth stop (2) in the

hole of the additional handle.

•

Set the depth stop and retighten the thumb

screw.

•

Now drill the hole until the depth stop touches

the workpiece.

5.3 Fitting the drill bit (Fig. 5)

Always pull the power plug before making adjust-

ments to the equipment.

•

Release the depth stop as described in 5.2

and push it towards the additional handle.

This provides free access to the chuck (1).

•

This hammer drill is fitted with a keyless

chuck (1).

•

Open the chuck (1). The drill bit opening must

be large enough to fit the drill bit into.

•

Select a suitable drill bit. Push the drill bit as

far as possible into the chuck opening.

•

Close the chuck (1). Check that the drill bit is

secure in the chuck (1).

•

Check at regular intervals that the drill bit or

tool is secure (pull the mains plug).

6. Operation

6.1 ON/OFF switch (Fig. 6/Item 5)

•

First fit a suitable drill bit into the tool (see

5.3).

•

Connect the mains plug to a suitable socket.

•

Position the drill in the position you wish to

drill.

To switch on:

Press the ON/OFF switch (5)

Continuous operation:

Secure the ON/OFF switch (5) with the locking

button (4).

To switch oﬀ :

Press the ON/OFF switch (5) brieﬂ y.

6.2 Adjusting the speed (Fig. 6/Item 5)

You can inﬁ nitely vary the speed whilst using the

tool.

•

Select the speed by applying a greater or les-

ser pressure to the ON/OFF switch (5).

•

Select the correct speed: The most suitable

speed depends on the workpiece, the type of

use and the drill bit used.

•

Low pressure on the ON/OFF switch (5): Lo-

wer speed (suitable for: small screws and soft

materials)

•

Greater pressure on the ON/OFF switch (5):

Higher speed (suitable for large/long screws

and hard materials)

Tip: Start drilling holes at low speed. Then increa-

se the speed in stages.

Beneﬁ ts:

•

The drill bit is easier to control when starting

the hole and will not slide away.

•

You avoid drilling messy holes (for example

in tiles).

6.3 Preselecting the speed (Fig. 7/Item 6)

The speed controller (6) enables you to deﬁ ne the

maximum speed.

•

Set the speed controller (6) to the required

position.

•

With the On/Off switch (5) pressed right in,

Anleitung_TE_ID_1050_1_CE_SPK7.indb 17Anleitung_TE_ID_1050_1_CE_SPK7.indb 17 25.11.13 13:0525.11.13 13:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TE-ID 1050-1 CE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info