Bedienungsanleitung Einhell TE-JS 100 (Seite 21 von 90) (Englisch, Dänisch, Schwedisch, Norwegisch)

606818

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

- 21 -

5.2 Changing the saw blade

(Figs. 3/Item 12)

 Important.

•

You can fit or replace saw blades without

using any other tools.

•

Pull out the mains plug before you fit or repla-

ce a saw blade.

•

Set the selector switch for pendulum action

(8) to position D (see Fig. 13).

•

The teeth of the saw blade are very sharp!

•

Remove the safety guard (15).

•

Press the blade holder (14) and insert the

saw blade (12) into the blade holder (14) as

far as the stop (Fig. 3). The teeth on the saw

blade must be pointing forwards.

•

Allow the blade holder (14) to slide back to

starting position. The saw blade (12) must sit

in the guide roller (10).

•

Check that the saw blade (12) is securely

mounted in the blade holder.

•

To remove the saw blade, follow the instruc-

tions above in reverse order.

5.3 Installing the parallel stop (Fig. 4/Item 11)

•

The parallel stop (11) enables you to saw

parallel cuts.

•

Undo the two locking screws (13) on the so-

leplate (7).

•

Now slide the parallel stop into the guides on

the soleplate (7). You can fit the parallel stop

(11) on either the left or right of the equip-

ment.

•

The guide strip must always face downwards.

Set the required distance using the measu-

rement scale on the parallel stop (11) and

tighten the locking screws (13) again.

5.4 Setting the soleplate for miter cuts (Fig. 5)

•

Undo the locking lever (16) on the soleplate.

•

Pull the sole plate (7) backwards slightly. The

soleplate can now be swiveled a maximum

45° to the left and right.

•

If the soleplate (7) is pushed back to the

front again it will only function in the locking

positions at 0°, 15°, 30° and 45°, which are

marked on the graduated scale for the sole-

plate (9). Move the soleplate into the required

position and refasten the locking lever (16).

•

However, the soleplate (7) is also easily set

to another angle. To do so, slide the soleplate

(7) backwards, set the desired angle and re-

fasten the locking lever (16).

Important. For miter cuts you must remove the

locking screws for the parallel stop (13) and the

splinter guard (20).

5.5 Adapter for dust extraction system

(Fig. 6/Item 5)

•

Connect your jigsaw to a vacuum cleaner

using the adaptor for dust extraction (5). This

will provide excellent dust extraction on the

work piece. The benefits are that you will pro-

tect both the equipment and your own health.

Your work area will also be cleaner and safer.

•

Dust created when working may be dange-

rous. Refer to the section entitled “Safety

instructions”.

•

Fit the adapter (5) as shown in Fig. 6. The

adapter (5) must audibly engage to ensure

that it is secure in the soleplate (7). The adap-

ter for chip extraction (5) cannot be used for

miter cuts.

•

Fit the vacuum tube of the vacuum cleaner

onto the adaptor opening (5). Check that the

connections are air-tight.

5.6 Line guide (Fig. 7-9/Item 19)

Using the line guide (19) you can carry out exact

cuts following cutting lines marked on the work-

piece. Fit the line guide by mounting it on the top

of the soleplate (7) and letting it lock in place at

the bottom, as shown in Fig. 7. Use the mark (a)

for the 0° angle setting (Fig. 8) and the mark (b)

for the 45° angle setting (Fig. 9). See point 5.4 for

information about the angle setting.

Important. Carry out a trial cuts in a piece of

waste wood.

5.7 Splinter guard (Fig. 10/Item 20)

The splinter guard ensures that the material you

want to cut does not splinter or crack during sa-

wing. Insert it into the soleplate from underneath

as shown in Fig. 10.

Important. The splinter guard (20) can be

used only for 0° cuts and must be removed

for miter cuts up to 45°!

Anleitung_TE_JS_100_SPK1.indb 21Anleitung_TE_JS_100_SPK1.indb 21 23.01.13 11:4123.01.13 11:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TE-JS 100 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell TE-JS 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info