Bedienungsanleitung Einhell WW 2000 R (Seite 15 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

605984

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

- 15 -

5. Before starting the equipment

Observe point 1 - Safety information.

Controls (buttons) (Fig. 2)

10 Desired Temperature + / Time Preselection +

11 Function Selection

12 On/Standby

13 Desired Temperature - / Time Preselection -

14 Time Preselection

Inserting batteries (Fig. 3-4):

1. Open the battery compartment cover by

pressing the lock (A) towards the middle and

pulling the battery compartment out at the

same time.

2. Insert the battery (B) in the battery compart-

ment with the positive pole facing down.

3. Press the battery compartment cover into the

remote control.

As the end user you are legally required to return

spent batteries. You can hand them in at public

collection points provided by your council or sales

outlets where batteries of this type are sold.

6. Operation

Warning! Before using the equipment for the ﬁ rst

time, check that the voltage supply is the same as

the voltage details set out on the rating plate.

•

Read the safety regulations in section 1.

•

When the equipment is used for the first time

or after a long period of rest, it may emit an

odor for a short time. This is not a fault.

All modes and functions can be set using the but-

tons on the appliance as well as with the remote

control. The remote control requires a CR 2032

button cell (included in delivery).

6.1 Switching on the appliance

The ON/OFF main switch (Fig. 1 / Item 4) is used

to disconnect the equipment completely from the

mains supply.

The ﬁ rst step when you want to use the appliance

is to turn on the main switch; the last step when

you no longer need the appliance is to turn oﬀ the

main switch. After the main switch is switched on,

the equipment will be in standby mode.

The heater shows the current equipment tem-

perature. The time display (00:00) for the timer

ﬂ ashes.

6.2 Heating mode (Fig. 2)

With the On / Standby button (Item 12) you can

switch the equipment on or to standby mode.

Press the On / Standby button (12) to switch on

the equipment. The desired temperature (default

setting 38°C) ﬂ ashes. The current equipment tem-

perature is then shown in the display, along with

the „Low heat output“ and „Blower“ symbols.

The time display (00:00) ﬂ ashes brieﬂ y and then

shows the operating time which has elapsed.

The heater operates with low heat output and the

blower.

Press the „Mode“ button (11) and by so doing

select the heating function in the following se-

quence.

Low heat output -> High heat output and blower

-> Frost protection function -> Low heat output

and blower -> Low heat output, etc.

6.3 Setting the desired temperature.

A desired temperature can be set between

5°C – 38°C, which is the temperature range of the

integrated temperature sensor (equipment tem-

perature). Press the „+“ or „-“ button to increase or

reduce the desired temperature.

For the equipment to heat, the desired tempera-

ture must be set higher than the indicated equip-

ment temperature. If the desired temperature is

exceeded by 2°C, the equipment will switch oﬀ

again.

In the frost protection function the temperature

is set to a default setting of 7°C and cannot be

adjusted.

6.4 Timer (Fig. 2)

Once you have ﬁ rst set the desired heating mode

and the desired temperature, you can program

a time for switching on („ON“) or a time for swit-

ching oﬀ („OFF“). You can select from between

1min to 23h 59min. It is also possible to combine

the switch-on time with the switch-oﬀ time.

Press the „Clock“ button (14) and select the timer

function in the following sequence.

Switch-on time hour -> Switch-on time minute ->

Switch-oﬀ time hour -> Switch-oﬀ time minute ->

Continuous operation

Anl_WW_2000_R_SPK7.indb 15Anl_WW_2000_R_SPK7.indb 15 13.03.15 09:3413.03.15 09:34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell WW 2000 R Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info