810941
19
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
19
USER INSTRUCTIONS
SCREW FEEDER FILLING
Loading the pellet screw feeder (coclea) is only neces-
sary if the boiler stove is new (and being switched on
for the rst time) or if the boiler stove had completely
run out of pellets.
To activate this loading, press the buttons
simultaneously, and the term “RI” is displayed.
The loading function ends automatically after 240” or if
you press the button.
IGNITION
With the boiler stove in stand-by, (after checking
that the grate is clean), press the
button and the
ignition procedure starts up.
The
term
“ON AC” (combustion starting) is dis-
played; after completing some control cycles and
when the pellets have actually ignited
the term
“ON
AC” is displayed (heating is being turned on).
This phase will last for a few minutes allowing the
ignition to be completed successfully and the boiler
stove's heat exchanger to be heated.
After a few minutes the boiler stove will move to the
heating phase, indicating
the term
“burn” and then,
during operation, it will display the delivery water
temperature set by the user and the power selected
by the automatic modulating system.
SWITCHING OFF
By pressing the button when the boiler stove is
ON, the switching o phase is started which in-
volves:
• Interruption to pellet supply
• Consumption of the last pellets in the grate, while
the ue fan stays on (typically for 10 min.)
• Cooling down of the boiler stove body maintaining
the pump in operation until the shutdown tempera-
ture is reached
• The term “OF” is displayed together with the num-
ber of minutes until switch-o .
During the switch-o phase, the boiler stove cannot
be switched on again; once the switch-o phase is
complete, the system will automatically go back to
standby.
AUTOMATIC OPERATION
It is necessary for the user to set the system deliv-
ery water temperature; this temperature must be as-
sessed in relation to the type and size of the system,
also considering the atmospheric temperature linked
to seasonal use.
The boiler stove, independently, regulates the power
according to the di erence between the set tem-
perature (set on the display) and the temperature
measured by the probe; when the desired temper-
ature is reached, the stove will operate at minimum
power on 1. You can increase the temperature
required by pressing the button or reduce it by
the pressing the
button.
The required temperature and the power that is
chosen automatically by the electronic modulating
system are displayed alternately.
ECONOMY FUNCTION
Function suitable for boiler stoves installed in small-
scale systems, or in mid-season when even mini-
mum power operation causes excessive heating.
This function, managed automatically, allows for
switching the boiler stove o once the set delivery
temperature is exceeded. The term “EC OF” will
be displayed indicating the minutes remaining to
switch-o .
When the delivery temperature falls below the set
value, the boiler stove switches back on automati-
cally. Request activation of this function, if required,
from the Technical Assistance Centre during initial
start-up.
REMOTE ACTIVATION FUNCTION (AUX
port)
By means of a special optional connection cable,
you can turn on/o the boiler stove using a remote
device such as a GSM remote telephone control, a
room thermostat, a command from a home auto-
mation system, or in any case from a device with
voltage free contact with the following logic:
Contact open = boiler stove OFF
Contact closed = boiler stove ON
Activation and deactivation occurs 10” after the last
command was transferred.
If the remote activation port is connected up, you
can still turn the boiler stove on/o using the control
panel; the boiler stove will always react in compli-
ance with the last order received, whether it is for
switching ON or switching OFF.
ROOM VENTILATION
To activate/deactivate the room temperature, press
the SET button for 3”; when “Air” is displayed, re-
lease the SET button, and using the +/- buttons set
to Air ON, if you want to activate ventilation or to Air
OFF, if you want to disable it.
Please note: the activation of ventilation is de-
pendent on this menu but also on a minimal water
temperature inside the boiler stove.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für EK63-EdilKamin DORE160 H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von EK63-EdilKamin DORE160 H

EK63-EdilKamin DORE160 H Bedienungsanleitung und Installationsanweisung - Deutsch - 28 seiten

EK63-EdilKamin DORE160 H Bedienungsanleitung und Installationsanweisung - Französisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info