Bedienungsanleitung Elac SUB 2040 ESP (Seite 14 von 24) (Deutsch, Englisch)

561014

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Description of operating controls and connecting terminals

Page 14 of 24

1 SUBWOOFER LEVEL

The subwoofer volume control should be adjusted to match the main speaker volume of your hifi or home cinema

system. As a general rule, subwoofer performance should not dominant the sound. Excessive bass leads to a

smeared soundstage and can result in unpleasant resonances at certain frequencies.

2 CROSSOVER FREQUENCY

Used to adjust the frequency at which the subwoofer crosses over. Signals above this crossover frequency are

gradually rolled off so they do not interfere with the main speakers. The adjustment of the crossover frequency will

depend on the size and frequency response of the main loudspeakers.

Loudspeaker configuration Crossover frequency

Home cinema set with LFE channel 125 - 180 Hz

Hifi/Stereo system with very small loudspeakers 125 - 80 Hz

Stereo system with satellites and subwoofer 80 - 125 Hz

Hifi/Stereo system with medium-sized bookshelf

speakers, smaller floor standing loudspeakers

(compatible with most ELAC loudspeakers)

50 - 80 Hz

3 MODE

Provided on the rear of the subwoofer, there are three positions available:

• AUTO Normal position. The ELAC subwoofer is switched to standby mode (indicator light LED glows red).

A sensor controls the inputs. If the appropriate bass signal is present, the power output stage is switched

on. Within tenth of a second, the subwoofer is ready for operation (indicator light LED glows green). The

subwoofer switches into standby mode again after a signal pause of more than 15 minutes (indicator light

LED glows red).

Note: If the automatic turn-on operation only responds to full volume, please increase the bass/LFE level

of your surround receiver and minimize the subwoofer level. This way, there will not be any changes in

bass level and the subwoofer will be turned on automatically at a lower volume.

• ON The subwoofer is operating continuously (indicator light LED glows green).

• OFF The subwoofer is in standby mode continuously (indicator light LED glows red).

To switch off the subwoofer completely, please switch the MODE control to OFF. A second later, the

Power switch can be turned off without any noise.

4 LED

ON / Standby LED. Glows green when device is switched on; glows red when device is in standby mode.

5 POLARITY

The subwoofer polarity can be switched to ‘+’ or ‘-‘. The best polarity should be determined by listening. The ‘ best’ polarity is

the position which results in a higher bass level.

6 LINE LEVEL IN

Input jack for connecting the ELAC SUB 2040 to the subwoofer output ‘BASS / SUB OUT / LFE’ of a surround amplifier or

surround receiver. For this connection, a commercially available mono cable with RCA phono connectors can be used. Do

not plug or unplug this cable while the subwoofer is in operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elac SUB 2040 ESP Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info