Bedienungsanleitung Elac SUB 2060D (Seite 27 von 48) (Deutsch, Englisch)

561007

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Description of the control and connection elements

Page 23

1 SPEAKER LEVEL IN

These are sockets for connecting the ELAC subwoofer to the loudspeaker outputs of an amplifier or surround re-

ceivers (also see next Section).

The bass sections of the sound signals incoming via the “LINE LEVEL IN“ and „SPEAKER LEVEL IN“ sockets are

all added and relayed via the subwoofer.

The input circuit has a symmetrically floating design, so that the ELAC subwoofer function like a passive speaker,

i.e. if required, amplifiers with bridge circuits can be connected without any reservations. In comparison to passive

loudspeakers much less current or power is drawn (around 1/40) and this independently of frequency. This means

that neither especially large cable sections nor “exotic” cable designs are required. The main loudspeakers receive

their power from the pre-connected amplifier (not from the ELAC subwoofer). Normally, 2 x 2.5 mm² are to be rec-

ommended. 2 x 1.5 mm² are sufficient without major sacrifices for “4 Ohm” loudspeakers up to a total length of

around 6 m; with “8 Ohm" loudspeakers up to approx. 12 m. Please feed the lines carefully into the terminals, no

short circuits due to protruding wires touching adjacent lines or the housing should be permitted.

2 LFE / MONO IN (UNBALANCED)

This cinch socket is designed for connecting the ELAC subwoofer to the “BASS” / “SUB OUT” / “LFE” output of a

surround amplifier / surround receiver. A standard mono-NF cable with cinch plugs is used for this connection.

During operation (operating mode set to “AUTO”) these plugs should not be plugged in or pulled out.

3 LFE / MONO IN (BALANCED) (only available with SUB 2080 D)

This XLR socket is designed for connecting the ELAC subwoofer to the “BASS” / “SUB OUT” / “LFE” output of a

surround amplifier / surround receiver. A symmetrical mono-NF cable with XLR plug and socket is used for this

connection. During operation (operating mode set to “AUTO”) these plugs should not be plugged in or pulled out.

4 REMOTE START

This phone-jack socket is designed for connecting the subwoofer to a remote output of a surround amplifier / sur-

round receiver. For this connection, a mono-LF cable with mono phone-jack plugs (3.5 mm diameter) is required.

The accepted trigger voltage may vary between 4V and 30V.

5 POWER (ON / OFF)

The device is switched on and off by the power switch.

After the signal links and the power supply have been connected with the supplied mains cable, you can turn on

the mains switch. In the case of prolonged absence, the device should be switched off to avoid unnecessary power

consumption.

NOTE: All-pole (galvanic) isolation of the ELAC subwoofer from the mains is only assured by removing the

mains plug! When the mains plug is plugged in and the mains switch on, there is residual current even in

stand-by mode (indicated by the blue LED at the front).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elac SUB 2060D Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info