646322
31
Zoom out
Zoom in
Vorherige Seite
1/46
Nächste Seite
1
2
5
3
4
Commissioning
GB
33
Check func onality of safety devices
Gas ghtness check
Boiler shut down
Check func onality of safety devices
All safety devices must be checked
for correct opera on/func oning
Safety devices on a standard boiler
are a water ow temperature sen-
sor, water return temperature sen-
sor, uegas temperature sensor and
ionisa on electrode.
These devices can be checked as de-
scribed below.
Flow temperature sensor (1)
Disconnect the plug from the sensor
while the boiler is switched on. This
should result in a lockout no. 20.
The lockout should disappear as soon
as the plug is placed back in posi on,
the boiler will restart.
Return temperature sensor (2)
Disconnect the plug from the sensor
while the boiler is switched on. This
should result in a lockout no. 40.
The lockout should disappear as soon
as the plug is placed back in posi on,
the boiler will restart.
Flue gas temperature sensor (3)
Disconnect the plug from the sensor
while the boiler is switched on. This
should result in a lockout no. 28.
The lockout should disappear as soon
as the plug is placed back in posi on,
the boiler will restart.
Ionisa on electrode (4)
Remove electrical connec on from
the ionisa on electrode while the
boiler is running, the boiler will go in
lockout no. 128. The boiler will try to
restart. With the electrical connec-
on removed, the restart will result
in lockout no. 133.
When the connec on is already
mounted, the restart will be success-
ful.
Measuring the ionisa on current can
be done by moun ng a mul -meter
(set to μA) in between the ionisa on
electrode and its electrical connec-
on.
The ionisa on current should always
be above 1.15 μA (60-70-80-120
models) 4,2 μA (100-140 models), in
normal condi ons it will be 6 μA and
above.
Gas ghtness check
Check the gas ghtness of all sealed
connec ons with an approved
soap or electronic gas analyzer, for
example:
Test points;
Bolt connec ons;
Gaskets of mixing system, etc.
Boiler shut down
When the boiler will not be used for
longer periods, shut down the boiler
by following procedure:
Switch the boiler in standby
opera on ( );
Switch o the boiler with the on/o
switch (5);
Disable power supply to the boiler
by deac va ng the mains isolator
switch in the boiler room;
Close the gas supply to the boiler.
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elco THISION L EVO wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info