Bedienungsanleitung Elco Ultramax PB 65 - 120 (Seite 20 von 66) (Englisch)

646321

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

ULTRAMAX PB 65 - 120

20 L290 ©MHS Boilers 13/12/2010

4.0 Installation instructions cont.

4.11 Connection to a combustion air supply and exhaust system C63x not tested in conjunction with

gas boiler.

The straight air/exhaust system for connection to a combustion air supply and exhaust system must not be

longer than 2m. A maximum number of three 90° angles are permitted for the installation. If combustion air is

supplied from the shaft, it must be kept free from any dirt.

4.12 Multiple assignment of exhaust systems (not part of the delivery program)

For modular flue systems, the calculation, layout and proof of functionality by the chimney manufacturer must

be taken into consideration.

Temperature (°C)

Volume flow (m³/h)

Mass flow (g/s)

Conveyance pressure (Pa)

Ultramax PB

Max./Min.

70 / 55

113 / 16

31 / 4

230 / 10

70 / 55

149 / 30

41 / 8

230 / 15

100

70 / 55

168 / 34

46 / 9

230 / 15

120

70 / 55

209 / 42

58 / 12

230 / 15

Flue System

The Ultramax PB Boilers have been tested using 110/150 Concentric Flue and as a result of the

examination, the appliances may be used with up to 15m of Concentric Flue Pipe plus 4 x 93 degree bends

plus a Concentric Terminal.

If planning to install a non room sealed flue; the following data will be of assistance:

Boiler Model

PB 65

PB 85

PB 100

PB120

Max Resistance of Flue

230

1m Length 110mm Ø PP Flue

Gas Tube

1.25

2.25

3.0

4.0

110mm Ø 93º PP Bend

1.25

2.25

3.0

4.0

110mm Ø 45º PP Bend

1.0

1.8

2.4

3.2

110mm Ø Open Termination with

Bird Mesh Guard

1.25

2.25

3.0

4.0

4.13 Ventilation / exhaust system

Applicable local regulations must be complied with when installing the exhaust system. The Ultramax PB

heating boiler must be operated with an approved exhaust system only. Customer supplied exhaust systems

must be resistant to moisture, corrosion and condensate, and must comply with all static and operational

requirements. The chimney design should be such that resistance to flow and therefore static pressure within

the system is minimised. The termination should be open with a mesh only.

The connection between flue and Ultramax PB must be sloped (3%) so that the accumulating condensate

may flow back from the exhaust pipe. This connection should have as few bends as possible. The exhaust

vent shall have inspection openings to current Standards and Codes of Practice.

4.14 Exhaust Pipes

Horizontal pipe layout must be avoided in order to avoid any puddling of condensate. You must ensure that

the various components are connected and sealed tightly. Any assembly shall use 45° bends. Vertical parts

shall be fastened with straps.

4.15 Placement and Distances

Minimum distances must be maintained in order to enable free access for operation and maintenance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elco Ultramax PB 65 - 120 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info