Bedienungsanleitung Eldom RH01W (Seite 15 von 76) (Deutsch, Englisch, Holländisch, Französisch)

782553

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

TECHNICAL DESCRIPTION

The electric wall-mounted convector heater is a household appliance intended to heat air in living rooms and maintain a specified

temperature.

APPLIANCE INSTALLATION

The heater installation must strictly comply with standards and rules in force in the country.

The convector heater has a degree of protection against Class II electrical current and is splash-proof (IP24). It can be installed

in living rooms, including in Zone 2 of bathing rooms, but so that controls must not be accessible to persons taking a shower or

bath - please refer to Fig. 1.

When installing the appliance it is necessary to comply with the minimum prescribed distances from various obstacles and surrounding

objects as shown in Fig. 2.

Do not install the appliance:

џIn places with compulsory draft, which can disrupt the control settings (under natural or forced ventilation apertures, fans,

etc.).

џUnder, over and in front of sockets (rosettes), please refer to Fig. 6.

When installing the heater on locations of high altitudes take into account that it may impact the temperature of the outlet air (by

increasing it with about 10 C when the altitude changes with 1000 m)

Take carefully the heater out of its packaging and keep it at a conventional place for any future needs.

Place the appliance with the front side to the ground without still removing the protective styrofoam side panels (Fig. 3). Please refer to

the figures on the second page of this booklet.

Unfasten the suspension stand according to the diagram shown in Fig. 3.

The installation of the convector heater on a reinforced concrete or solid brick wall can be carried out after the stand is secured to the

wall according to Fig. 4, using the screws and dowels available in the package.

Place the appliance on the stand as shown in Fig. 5.

The convector power cord plug can be connected to a protected single phase power outlet with voltage 230 V~. The socket must be

located so that it is easily accessible after fitting the device into its working position.

It is forbidden to ground the appliance!

It is forbidden to increase the distance from the wall to the convector heater, which is secured by the suspension stand provided by the

manufacturer!

EN EN

All data and dimensions provided are approximate.

Model

Power / Voltage

Length W [mm]

L [mm]

1000 W / 230 V~

716 / 592

480 / 200±2

1500 W / 230 V~

916 / 688

480 / 200±2

2000 W / 230 V~

1116 / 880

890 / 480±2

2500 W / 230 V~

1366 / 1072

890 / 480±2

3000 W / 230 V~

1566 / 1216

890 / 480±2

150

230

150

Convector heater on / off

switch

Control panel

Suspension

stand

RH10N(W) /

RH01W10X-W

453

106

434

RHххN(W)RH01WxxX-W

RH15N(W) /

RH01W15X-W RH20N(W) /

RH01W20X-W RH25N(W) /

RH01W25X-W RH25N(W) /

RH01W25X-W

RH01W05X-W

500 W / 230 V~

400

200±2

ATTENTION!

It is recommended to keep the distance of 150 mm

between the convector and the floor of the room.

The minimum allowable floor distance to the lower end of

the convector is 60 mm. Failure to comply shall reduce the

appliance safety.

242 / 257

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eldom RH01W Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info