Bedienungsanleitung Eldom RH01W (Seite 18 von 76) (Deutsch, Englisch, Holländisch, Französisch)

782553

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Controllers features and settings

Setting specific temperature

Use buttons 2 and 3 to change the temperature. The maximum temperature that can be set is 28 °C and the

minimum is 7 °C. Pressing any of these two buttons shall display the current temperature set. With the

following keystrokes you may change the assignment in the desired direction. If no new button is pressed

within 5 seconds, the new task shall be memorized and automatically the unit shall switch to the main screen. If

any of the buttons 2 or 3 shall be held for more than 0.7 s, the temperature set point value automatically starts

to increase or decrease with the speed of 4 units per second.

Adjusting the power of the appliance

When the measured temperature is lower than the set one, the convector heater switches on - its power

indicator scale fills in. The more the temperature is approaching the set one, the less is the filling of the scale.

When the set temperature is reached, the indicator goes out. The power control function can be switched off by

the sub-menu Settings by deactivating the check-mark Reg. power. In this case, under all operating modes,

the convector heater shall run at full power during heating or shall be completely switched off when the

temperature set is reached.

Child lock

This feature locks all control panel buttons, limiting the possibility of unauthorized access to the controller

settings. The feature is turned on by the child protection sub-menu, followed by the instruction on the display - Press OK to lock the

buttons. The following message is displayed - Buttons are locked!. It is suitable to press the button 1 to exit the settings menu, displaying

a symbol illustrating child protection . To turn off child protection, you must hold the OK button for a time longer than 7 seconds.

Protection against convector heater falling

If the convector heater is knocked down while switched on, the controller switches off the heater, the unit displays a message Convector

fell, and activates an audible alarm. The alarm will be deactivated automatically after restoring the appliance normal position or by

pressing button 1 to switch off the convector heater. It may be a malfunction if the convector heater was stored in a cold place for a long

time and then placed in a significantly warmer place.

Open window feature

The controller has a built-in feature for recognizing an open window that automatically stops heating. An open window icon appears on

the display. This feature operates in two modes - Smart and On. Switching from one mode to the other is done by changing the setup

Open window in sub-menu System Settings. When the setting is Smart, the convector heater shall continue heating as soon as it

detects that the window is closed or after 15 minutes have elapsed since the protection mode is activated, while the heating mode ON

shall continue for 60 minutes once the mode is activated. The Open window feature is disabled when you press button 1, which switches

the convector heater to Standby mode, or from the sub-menu System set Open Win to Off

Keeping the system date and time

The controller unit keeps the system date and time

For all Timer / Program, Delayed Start, and Power Meters to work correctly, the date and time must be verified. Verification is set from

the main menu, sub-menu Time and Date. The auto-enable option check box works only on models with WiFi control.

Remote control over the Internet

This feature requires an additional WiFi module installed in the configuration of the following convector heater models: RH10NW,

RH15NW, RH20NW, RH25NW, RH30NW, RH01WxxW-x.

If the appliance you bought has a model number corresponding to one of the listed above - please read the

supplement to this Instruction manual.

Two stage overheat protection

Apart from the electro-mechanical thermal protection, the convector heaters also rely on the electronic

protection built into the controller. This protection prevents accidental overheating of the appliance inside. The

feature temporarily interrupts the heating until the temperature drops below the allowed maximum. A symbol is displayed.

Color graphic display

The electronics have a high-resolution color display. The Display sub-menu sets Brightness settings (from 1 to 10) and Dimming

activation check-box. Dimming automatically reduces the brightness of the display 30 seconds after the last press of a button (the

feature does not work at set brightness -1).

Reporting consumed electricity

The controller supports separate counters for daily and nocturnal electricity consumption. In order to report correctly the concerned

data, it shall be necessary to set the unit power from the sub-menu Settings - Power setting, and the start time of each tariff in the Home

tariffs sub-menu. When the OK button is pressed once, the electricity consumption counters are displayed and

the date and time of their last reset. While this screen is displayed, if the OK button is held for 2 seconds, then

the counters are reset and the resetting date and time are recorded. Next time you press the OK button, it

switches to the screens with a graph of the electricity consumed by hours. The controller shall store such

information for the last 7 days. By pressing the ▲ or ▼ buttons, the charts shall change with the days for

EN EN

Eldom RH01W Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info