Bedienungsanleitung Electrolux eea 120 (Seite 32 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

362297

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

0 Remove the plastic attachment and

rinse both under running water

(figure 14).

0 Place the plastic attachment back into

the drip tray.

0 Push the clean drip tray back into the

appliance and place the drip grating

back in.

Cleaning the brew filter

From time to time check the brew filter

to ensure that the holes in the filter

have not become blocked by coffee

particles. The brew filter is located on

the underside of the brew head.

If the holes have become blocked:

0 Unscrew the brew filter using a coin

(figure 15).

0 Remove the brew filter and seal

(figure 16/1) and remove the brew fil-

ter’s seal (figure 16/2).

0 Clean the brew filter with warm water

and a brush.

0 Rinse the seal with warm rinse water.

If the appliance is to be transported at

temperatures below zero:

0 Empty the water tank.

0 Turn the selector dial (figure 1/E) to

the position and let the appliance

dry.

Decalcifying

If the espresso is flowing through the

filter at a slower rate than usual, it is

time for the appliance to be decalci-

fied.

We recommend that you decalcify the

machine once every three months. If

you live in an area with hard water the

decalcifying procedure may have to be

carried out more often.

We recommend to use only the original

Electrolux decalcifying tabs

(PNC 900 195 537/7).

Important: Prior to decalcifying, re-

move the brew filter (figure 1/T) and

the brew filter’s seal, as described in

the section “Cleaning the brew filter”

(figures 15, 16).

First pour the water into the water

tank, then add the decalcifier; never in

the reverse order. At least 0.5 litres of

water must be used. The decalcifier

should be added accordingly.

0 Remove the power plug from the

power point and allow the appliance to

cool.

0 Place the filter holder in position with-

out the filter.

0 Place a sufficiently large container

under the filter holder.

0 Insert the power plug into the power

point and switch on the appliance.

0 Afterwards, turn the selector dial (fig-

ure 1/E) to the position and let

approx. 1/3 of the decalcifier flow

through the system.

0 Then switch off the appliance and

allow the decalcifying solution to act

for approx. 10 minutes.

0 Allow the rest of the decalcifying solu-

tion to rinse the brew head.

0 Then thoroughly clean the water tank.

0 Fill the water tank with fresh water

and allow all of the water to flow over

the brew head.

Repeat the procedure if there is a lot of

limescale.

0 After decalcifying the appliance,

replace the brew filter and seal.

What to do if…

• the espresso temperature is too low:

– Carry out the brewing procedure

without using espresso grounds, but

using the filter and filter holder, in

order to preheat the system.

–Preheat the cups.

– Decalcify the appliance.

• the flow speed decreases noticeably:

– Do not press the espresso grounds

too firmly into the filter.

– Do not grind the espresso grounds

too finely (“medium” fineness).

– Decalcify the appliance.

822_949_384 EEA120_130_Elux.book Seite 32 Freitag, 28. Dezember 2007 5:42 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux eea 120 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info