451879
44
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
44
20b
20b
7-16
4
5
6
13
9
8
14
18
20a
20a
8
19
8
9
D
G
H
11
11
10
17
F
2
2
1
12
G
1
3
15
Installation
Wall unit mounting - Fig. 10
Disconnect the hood during electrical connection, by turning the home mains switch off.
Remove the 2 screws fitted inside the lower part of the hood at the points in which it is
fixed to the suction unit (see also operation 3).
Rest the suction unit on a flat surface and
thread the lower part of the hood onto it
(1).
Make all the electrical connections
between the two parts (2).
Fasten the hood to the suction unit using
8 screws (3).
Sign the wall with a center line, this will
aid mounting procedure (4), position the
template so that the mid line printed on
the template matches with the center
line previously signed, the lower side of
the template corresponds to the lower
side of the hood once mounted (5).
Drill two holes Ø 8mm and fix the
support bracket with two wall plugs
and screws (6).
Hang the hood (7) adjust its position
(8-9) and from the inside of the hood
sign one point for definitive fixing
(10), remove the hood (11) and drill
an hole Ø 8mm (12), fit a wall plugs
(13).
Drill two holes Ø 8mm on the upper
side close to the ceilling (14), fit
two wall plugs and fix the chimney
support with two screws (15).
Hang the hood again (16).
Fix it definitively with a screw
(17). To simplify the mounting
operation remove the carbon
filter frame.
In case the hood is to be used in
filter version, mount the deflector
F on the chimney support G with four
screws 2,9x6,5 and fit an exhausting pipe
(18) to connect deflector to the outlet hole D of
the hood.
In case the hood is to be used in exhausting version,
then the deflector must not be mounted and fit an
exhausting pipe (18) to connect outlet hole D of the hood to the outside.
Make electrical connection (13), but leave the hood disconnected from the home
general electric panel.
Fix the chimney (16a) to the chimney support (16b).
Slide down the lower section on the proper housing on top of the hood. Connect the hood
the the home general electric panel and check if the hood work properly.
Fig. 10
44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Electrolux EFC 9460 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info