Bedienungsanleitung Electrolux EHG 6430 (Seite 16 von 48) (Deutsch, Englisch, Holländisch, Französisch)

451957

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

– it can be easily examined in order to

check its condition.

The control of preservation of the flexible

pipe consists in checking that:

– it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

– the material is not hardened, but shows

its correct elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not re-

pair the pipe, but replace it.

Important! When installation is complete,

make sure that the seal of each pipe fitting

is correct. Use a soapy solution, not a

flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the in-

jectors and replace them with the ones

which are necessary for the type of gas

you use (see table in Technical Data

section).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating label (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this label in the package of the injectors

supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you

must fit an applicable pressure adjuster on

the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the control knob.

4. With a thin screwdriver, adjust the by-

pass screw position. If you change from

natural gas 20 mbar to liquid gas, fully

tighten the adjustment screw in. If you

change from liquid gas to natural gas 20

mbar, undo the by-pass screw approxi-

mately 1/4 of a turn.

Minimum adjustment screw

5. Make sure the flame does not go out

when you quickly turn the knob from the

maximum position to the minimum posi-

tion.

Electrical connection

• Ground the appliance according to safety

precautions.

• Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the lo-

cal power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a correct

plug, able to support the load marked on

the identification plate. The plug has to

be fitted in a correct socket.

• Any electrical component must be instal-

led or replaced by the Service Force

Centre technician or qualified service per-

sonnel.

• Always use a correctly installed shock-

proof socket.

• Make sure that there is an access to the

mains plug after installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

• The appliance must not be connected

with an extension cable, an adapter or a

multiple connection (risk of fire). Check

that the ground connection is in conform-

ity with the standard and regulations

force.

• The power cable must be placed in such

a way that it does not touch any hot part.

16 electrolux

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux EHG 6430 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info