Bedienungsanleitung Electrolux esf 65710 x (Seite 45 von 96) (Deutsch, Englisch, Holländisch, Französisch)

127983

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Proceed as follows:

• Remove the machine’s worktop by un-

screwing the two rear retaining screws (1),

pull the worktop from the back of the ma-

chine (2) and slide out the front slots, lifting

the worktop (3).

Insert the machine after adjusting the level-

ling with the adjustable feet. When inserting

the machine, ensure that the water inlet and

drain hoses are not kinked or squashed.

During all operations that involve accessibility

to internal components the dishwasher has

to be unplugged.

Be sure that once the appliance has been in-

stalled, it is easily accessible for the service

engineer in the event that a repair is required.

If the dishwasher is later used as a free-

standing appliance, the original worktop

must be re-mounted.

The plinth on free-standing appliances is not

adjustable.

Levelling

Good levelling is essential for correct closure

and sealing of the door.

When the appliance is correctly levelled, the

door will not catch on either side of the cab-

inet .

If the door does not close correctly, loosen

or tighten the adjustable feet until the ma-

chine is perfectly level.

Water connection

Water inlet connection

This appliance can be connected to either a

hot (max. 60°) or cold water supply.

With a hot water supply you can have a sig-

nificant reduction of energy consumption.

This however, depends on how the hot water

is produced. (We suggest alternative sources

of energy that are more environmentally

friendly as e.g. solar or photovoltaic panels

and aeolian).

For making the connection itself, the cou-

pling nut fitted to the appliance water inlet

hose is designed to screw onto a 3/4" thread

spout or to a purpose made quick-coupling

tap such as the Press-block.

The water pressure must be within the limits

given in the 'Technical data'. Your local Wa-

ter Authority will advise you on the average

mains pressure in your area.

The water inlet hose must not be kinked,

crushed, or entangled when it is being con-

nected.

The appliance features inlet and drain hoses

which can be turned either to the left or the

right to suit the installation by means of the

locknut. The locknut must be correctly

fitted to avoid water leaks.

Attention! NOT all dishwasher models of

have inlet and drain hoses provided with

a locknut. In this case, this facility is not

available.

If the appliance is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

DO NOT use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with safe-

ty features which will prevent the water

used in the appliance from returning

back into the drinking water system. This

appliance complies with the applicable

plumbing regulations.

Water drain connection

The end of the drain hose can be connected

in the following ways:

electrolux 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux esf 65710 x Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info