Bedienungsanleitung Electrolux esf 66710 x (Seite 94 von 96) (Deutsch, Englisch, Holländisch, Französisch)

126275

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

right to suit the installation by means of the

locknut. The locknut must be correctly

fitted to avoid water leaks.

Attention! NOT all dishwasher models of

have inlet and drain hoses provided with

a locknut. In this case, this facility is not

available.

If the appliance is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

DO NOT use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with safe-

ty features which will prevent the water

used in the appliance from returning

back into the drinking water system. This

appliance complies with the applicable

plumbing regulations.

Water drain connection

The end of the drain hose can be connected

in the following ways:

1. To the sink outlet spigot, securing it to the

underside of the work surface. This will

prevent waste water from the sink run-

ning into the machine.

2. To a stand pipe provided with venthole,

minimum internal diameter 4 cm.

The waste connection must be at a height of

between 30 cm (minimum) and 100 cm

(maximum) from the bottom of the dishwash-

er.

The drain hose can face either to the right or

left of the dishwasher

Ensure the drain hose is not bent or squash-

ed as this could prevent or slow down the

discharge of water.

The sink plug must not be in place when the

machine is draining as this could cause the

water to syphon back into the machine.

If you use a drain hose extension it must be

no longer than 2 metres and its internal di-

ameter must be no smaller than the diameter

of the hose provided.

Likewise the internal diameter of the cou-

plings used for connections to the waste out-

let must be no smaller than the diameter of

the hose provided.

When connecting the drain hose to an under

sink trap spigot, the entire plastic mem-

brane (A) must be removed. Failure to re-

move all the membrane will result in food

particles building up over time eventually

blocking the dishwasher drain hose spigot

Our appliances are supplied with a se-

curity device to protect against the re-

turn of dirty water back into the machine.

If the spigot of your sink has a "no return

valve" incorporated this can prevent the

correct draining of your dishwasher. We

therefore advise you to remove it.

To avoid water leakage after installation

make sure that the water couplings are

tight.

Electrical connection

Warning! Safety standards require

the appliance to be earthed.

Prior to using the appliance for the

first time, ensure that the rated volt-

age and type of supply on the rating

plate match that of the supply where

the appliance is to be installed. The

fuse rating is also to be found on the

rating plate.

94 electrolux

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux esf 66710 x Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info