Bedienungsanleitung Electrolux ESI 63010 (Seite 46 von 68) (Deutsch, Englisch, Holländisch)

451755

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Fault code and malfunction Possible cause and solution

• continuous flash of the start/can-

cel indicator light

• 1 flash of the end indicator light

The dishwasher does not fill with wa-

ter

• The water tap is blocked or furred with limescale.

Clean the water tap.

• The water tap is closed.

Open the water tap.

• The filter in the water inlet hose is blocked.

Clean the filter.

• The connection of the water inlet hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the start/can-

cel indicator light

• 2 flashes of the end indicator light

The dishwasher will not drain

• There is a blockage in the sink spigot.

Clean the sink spigot.

• The connection of the water drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the start/can-

cel indicator light

• 3 flashes of the end indicator light

The anti-flood device operates

• Close the water tap and contact your local Service Force

Centre.

The programme does not start • The appliance door is not closed.

Close the door.

• Mains plug is not connected in.

Put in the mains.

• The fuse has blown out in the household fuse box.

Replace the fuse.

• Delay start is set.

Cancel the delay start to start the programme immediately.

After the check, switch on the appliance.

The programme continues from the point of

interruption. If the malfunction shows again,

contact your Service Force Centre.

These data are necessary to help you quick-

ly and correctly:

•Model (Mod.)

• Product number (PNC)

• Serial number (S.N.)

For these data, refer to the rating plate.

Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of

load and soil.

• The baskets are loaded incorrectly so that water cannot reach all

surfaces.

• Spray arms do not turn freely because of incorrect arrangement of

the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the

dishes

• The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky

spots or a bluish coating on

glasses and dishes

• Decrease the rinse aid dosage.

Dry water drop signs on

glasses and dishes

• Increase rinse aid dosage.

• The detergent can be the cause.

46 electrolux

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux ESI 63010 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info