Bedienungsanleitung Electronics Line EL-2645 (Seite 1 von 1) (Englisch)

580184

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

EL-2645 / PI Wireless Motion PIR Detector Standard & Petimmune – Funkbewegungsmelder Standard & Haustierimmun - Détecteur de mouvement sans fil PIR Standard & Petimmune - Draadloze PIR Detector Standard & Petimmune

5IN1561

International Headquarters:

Electronics Line 3000 Ltd.

14 Hachoma St., 75655

Rishon Le Zion, Israel

Tel: (+972-3) 963-7777

Fax: (+972-3) 961-6584

All data is subject to change without prior notice techniques

In no event shall Electronics Line be liable for an amount in excess of EL3K’s original selling price of this product, for any loss or damage

whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.

Hereby, Electronics Line declares that this sensor/transmitter is in compliance with the essential requirements and other relevant provisions

of Directive 1999/5/EC.

06/2011 5IN1561

The EL-2645 / PI is a Wireless Motion PIR

Detector designed for use with Electronics Line

supervised wireless range of receivers.

Location of Detector

Consider the following before mounting the

detector:

 Select a location from which the pattern of

the detector is most likely to be crossed

by a burglar, should there be a break in.

 Do not place bulky objects in front of the

detector.

 Avoid a location that comes in direct

contact with radiators, heating/cooling

ducts or air conditioners.

 Do not place the detector in front of

windows subject to direct sunlight or

drafts.

Installation Instructions

1. Open the housing by removing the front

cover. To do so, insert a screwdriver in

the release slot (located at the bottom of

the detector between the front and back

cover). Turn the screwdriver 90º to

release the cover.

2. Remove the PCB by turning counter-

clockwise and removing the 'PCB Screw'.

Note: Do not touch the face of the PYRO

sensor.

3. Apply battery power by removing the

isolator that separates the battery from the

contacts on the battery holder.

4. Set the receiver to Registration mode and

cause Tamper or Alarm transmission. Wait for

the receiver to indicate that the transmitter has

been registered successfully. Write the

number of the zone and the transmitter

number (if applicable) on the sticker provided.

Affix the sticker inside the front cover for future

reference.

Note: Alternatively, the Detector can be

registered to the receiver by manually

entering the transmitter's serial

number.

5. Choose an appropriate mounting height from

2.2 – 2.5 and test the transmitter from the exact

mounting position before permanently mounting

the unit.

Note: If you choose mounting height other

than recommended (which is not

advised), please perform a walk test to

check the lens coverage. The

recommended mounting height is the

best in terms of detection area.

6. Knock out the mounting holes and attach

the base to the wall.

7. If using the rear tamper switch, insert a

screw into the rear tamper mounting hole

located in the center of the back cover –

see Figure 3. When the detector is

removed from the wall, the screw causes

the tamper release to break away from the

back cover and the rear tamper switch is

released.

8. Mount the PCB on the base cover and

replace the PCB Screw.

9. Replace the front cover.

DIP Switches Settings

Switch

PIR sensitivity

* Off: Low

On: High

Operation mode:

* Off: Normal mode – Every 3 minutes.

After each detection the sensor initiates

a three-minute delay during which

alarm transmissions will not be sent

On: Walk Test mode. An alarm

transmission is sent after each

detection

Supervision Time:

Off: As supervision message will be

sent to the alarm panel every 15

minutes

* On: As supervision message will be

sent to the alarm panel every 65

minutes

LED

Off: LED disabled

* On: LED enabled

*=Default

Operation Modes

Warm-up Time: The detector will need to warm up

for the first 90 seconds after applying power.

Walk Test Mode: A walk test is performed in order

to determine the lens coverage pattern of the

detector – see Figure 2. Walk Test mode cancels

the delay time between detections, enabling you to

perform an efficient walk test.

To walk test the detector:

1. Set DIP 2 to ON.

2. Walk across the scope of the detector

according to the detection pattern

selected.

3. Confirm that the LED activates and

deactivates accordingly. Wait for ten

seconds after each detection before

continuing the test.

4. After completing the walk test. Set DIP-

2 to OFF.

LED Indication

The LED indicator is lit every time a transmission

is made. To enable/disable LED indication, refer to

DIP Switch Setting section for the appropriate DIP-

switch setting.

Note: The LED should only be disabled after

successfully walk testing the detector.

Changing Lenses

To change a lens, release the cavity seal using a

small screwdriver and fix the new lens into place

with the smooth side facing outwards. Verify that

the word TOP is located at the top of the lens

(alternatively a notch may appear on the bottom

edge of the lens) before snapping the cavity seal

back into place.

Battery Replacement

In case of a low battery (2.5 V and below), the

sensor low battery condition is reported to the

Control System and low battery message is

displayed

To replace a battery: Open the housing by

removing the front cover (see Installation

Instructions), replace the battery, and close the

front cover.

Note: Close the front cover immediately after

each battery replacement.

Technical Specifications

Frequency: 868.35, 433.92 MHz

Power: 3.6V ½ AA Lithium Battery

Caution: Fire, explosion and severe burn hazard!

Do not recharge, disassemble or heat above 100°C.

Current Consumption: 30mA (transmission), 8µA

(standby)

Pyroelectric Sensor: Dual Element

Maximum Coverage: 14 x 14m

Adaptive Temperature Compensation

RFI Immunity: According to EN 50130-4

Operating Temperature: -10 - 40°C

Fire Protection: ABS Plastic Housing

Dimensions: 110 x 60 x 45mm

Figure 1: PCB

1. Battery Holder

2. Antenna

3. LED Indicator

4. PCB Screw

5. DIP Switch

6. Tamper Switch

7. Pyro Sensor

8. Back Tamper

Figure 2: Lens Coverage

Note: The diagram shows the coverage

pattern for the detector fitted with a standard

lens of EL2645.

EL2645-PI has limited detection at the ground

to ignore animals

Rear tamper mounting

hole

Electronics Line EL-2645 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Electronics Line EL-2645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info