753500
14
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
14
ENGLISH
3.5 Control unit for default
machine settings
The individual components need to be
connected to each other before being
connected to the mains and before inital
operation. By default the components as
set for gas-shielded arc welding:
1. With the help of another person lift
the SWK (water cooling unit) and
place it on the Powerbox, to that its
feet stand between the pipes on the
rubber mat.
2. With the help of another person lift
the SDV (wire feed unit) and place it
onto the water cooling unit.
3. Connect the coolant hoses as illus-
trated below (see also the SWK
instructions).
4. Connect the cables as illustrated
below.
The Powerbox is mounted on a wheel
set. With fitted SDV and SWK the com-
plete welding machine is conveniently
moved to the workplace.
Danger!
Close the cylinder’s valve
before relocating.
Danger!
Note the hight weight of the
welding machine. It may get out of
control, especially on sloping
ground!
Walk along the intended way, before
you set off with the welding machine.
Ask another person for assistance, if
necessary!
5.1 Crane hoisting
The welding machine can be hoisted by
crane.
Danger!
Remove the gas cylinder
before hoisting.
Hoisting with the gas cylinder is for-
bidden!
1. Fit the hoisting straps as illustrated
below.
Caution!
At the workplace, secure the
machine against rolling away.
6.1 Manual arc welding
When setting the machine for manual
arc welding, you must:
1. Check all connections.
Disconnect earth cable (- pole) and
welding current supply cable
(+ pole).
2. Connect earth cable to the Power-
box - pole).
3. Connect welding cable to the weld-
ing current supply cable (+ pole).
6.2 Gas-shielded arc welding
1. Check all connections. Disconnect
earth cable (- pole).
The welding current supply cable
(Powerbox) must be connected to
the connector plug of the welding
current supply (SDV).
25 LED welding voltage [V]
26 LED arc length [%]
27 7-segment display (3 digits)
The display shows:
the value of the selected
parameter or
an error message.
28 Parameter adjustment
to adjust the selected parameter.
29 Wire thread-in button
(Manual Wire Feed Drive)
30 Operating mode selector switch
(Mode Selection)
31 Burnback time selector switch
(Wire burnback control)
32 Gas type selector switch
(Gas Type)
33 Wire diameter selector switchr
(Wire Diameter)
34 Wire type selector switch
(Wire Type)
4. Installation
34 33 32
29 30 31
5. Transport
6. Preparing for Operation
A
V
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elektra Beckum Mig Mag 502EP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info