Bedienungsanleitung Elektra Beckum Mig Mag 502EP (Seite 17 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

753500

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Caution!

Check all connections and

supply lines before switching ON.

Caution!

At the workplace, secure the

machine against rolling away.

8.1 Control unit

The operating parameters are set and

displayed at the control unit.

With the pushbutton for parameter

selection, the parameter to be displayed

or adjusted is selected.

The following parameters can be

selected and displayed:

−Wire feed [m/min]

−Welding current [A]

−Welding voltage [V]

−Arc length [%]

The selected parameter is indicated by

the LEDs and its value is displayed on

the 7-segment display.

Using the parameter adjustment the

desired value, except the welding volt-

age, is set.

Wire feed

Via the parameter wire feed the feed

speed of the wire feed drive is set. The

best value for welding voltage and weld-

ing current is computed by the machine,

dependent on the selected charateristics

curve.

wire feed value range:

−1.5 ... 19 m/min.

The value range available for adjustment

is dependent on the selected electrode

wire and the operating mode.

For manual arc welding the display is

disabled.

Welding current

The best current strength is determined

by the machine. During MIG/MAG weld-

ing the welding current can not be

adjusted. The set value can be adjusted

prior to welding via the parameter adjust-

ment.

For manual arc welding it is possible to

adjust the set value of the welding cur-

rent before the welding starts and also

during the welding process (actual

value).

Welding voltage

The welding voltage is displayed only. It

can not be adjusted.

Arc length

In MIG/MAG and pulsed MIG/MAG oper-

ating mode, the value set affects welding

voltage.

The adjustment range is from 50%

through 150%. 100% is the best operat-

ing point.

Note:

When using interconnecting torch

lead extensions, the occuring voltage

drop can be compensated by the param-

eter. In this case adjust to values of

110% ... 120%.

8.2 Gas-shielded arc welding

Caution!

Check before starting any

work:

−Correct electrode wire installed?

−Correct shielding gas connected?

−Welding gun correctly fitted

(liner, spiral liner, contact tip, gas

shroud, support tube)?

1. Attach earth cable at suitable loca-

tion of workpiece.

2. Open cylinder valve and set desired

gas flow rate.

Change gas shroud, if necessary.

3. Set main switch at Powerbox and

mains switch of SWK to ON.

4. Adjust the machine’s default setting.

Selet charateristics curve.

5. Change parameters, if required.

The welding machine is now opera-

ble.

8.3 Manual arc welding

1. Attach earth cable at suitable loca-

tion of workpiece.

2. Set main switch of Powerbox to ON.

3. Select welding process ELE-

KTRODE.

The welding machine is now opera-

ble.

8.4 Shutting down

1. Close gas cylinder valve.

2. Set main switch to "0".

3. Disconnect earth cable from the

workpiece.

4. Unplug power cable.

This welding machine contains no user-

serviceable parts.

Depending on dust accumulation, the

Powerbox and the SDV should be blown

out with condensate-free compressed

air.

Periodically check all components for

visible damage.

Contact a qualified electrician if any of

the cables are damaged.

For models 232/ 302/ 402/ 502 EP the

accessories mentioned below are rec-

ommended. These accessories have

been tested with the machine and

ensure operation without any problem.

AWelding guns for 232 EP

1) SB 24/3

2) SB 24/4

3) SB 24/5

BWelding guns for 302 EP

1) SB 36/3

2) SB 36/4

3) SB 36/5

CWelding gun for 402 EP and

232/302 EP with water cooling

1) SB 41/W3

2) SB 41/W4

3) SB 41/W5

DWelding guns for 502 EP

1) SB 51/W3

2) SB 51/W4

3) SB 51/W5

EEarth cable

1) 5 m, 25 mm2 for 232 EP

2) 5 m, 50 mm2 (copper jaws)

for 302/ 402 EP

3) 5 m, 70 mm2 (copper jaws)

for 502 EP

FInterconnecting torch lead exten-

sion

for 232/302 EP

1) 5 m, 50 mm2, gas-cooled

2) 10 m, 50 mm2, gas-cooled

GInterconnecting torch lead exten-

sion for 232/302/402 EP with water

cooling

1) 5 m, 50 mm2, water-cooled

2) 10 m, 50 mm2, water-cooled

HInterconnecting torch lead exten-

sion

for 402/502 EP

1) 5 m, 70 mm2, water-cooled

2) 10 m, 70 mm2, water-cooled

IPressure gauge with 2 gauges and

stop valve.

8. Operation

Shielding gas amount in l/min Aluminium Steel

Welding current in A

Gas shroud diameter

in mm

9. Maintenance

10. Available Accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elektra Beckum Mig Mag 502EP Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info