Bedienungsanleitung Elektra Beckum SK260 (Seite 12 von 36) (Deutsch, Englisch, Holländisch, Spanisch)

658064

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SK 200 SK 230 SK 260 SB 200 SB 230 SB 260

Mains voltage 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V

380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V

Mains frequency 50 H 50 Hz 50Hz 50Hz 50Hz 50 Hz

Welding steps stepless stepless stepless stepless stepless stepless

Current Range 25-200 A 25-230 A 25-260 A 20-200 A 20-230 A 30-260 A

Stepless at 220/240 V 25-110 A 25-114 A 25-120 A 20-110 A 20-114 A 30-135 A

Stepless at 380/415 V 40-200 A 40-230 A 40-260 A 30-200 A 36-230 A 75-260 A

Max. OCV

at 220 - 240 V 36.5 - 39 V 37.0 - 40 V 36.0 - 40 V 36.5 - 39 V 37.0 - 40 V 39.0 - 40 V

Max. OCV at 380 - 415 V 48.5 - 55 V 53.0 - 59 V 55 - 60 V 48.5 - 55 V 53.0 - 59 V 55.0 - 60 V

Max. input cap. at 220 - 240 V 4.3 kVA 4.5 kVA 4.4 kVA 4.3 kVA 4.5 kVA 4.5 kVA

Max. input cap. at 380 - 415 V 11.8 kVA 13.7 kVA 16.4 kVA 11.8 kVA 13.7 kVA 16.4 kVA

Working voltage 21.0-28.0 V 21.0-28.8 V 21.0-30.2 V 21.0-28.0 V 21.0-28.8 V 21.0-30.2 V

Cos - 220 - 240 V 0.77 (110 A) 0.77 (114 A) 0.80 (120 A) 0.77 (110 A) 0.77 (114 A) 0.8 (130 A)

Cos - 380 - 415 V 0.66 (200 A) 0.63 (220 A) 0.62 (260 A) 0.67 (200 A) 0.63 (220 A) 0.62 (260 A)

Duty cycle at max.

output 220 - 240 V* (25 / 40°) 25 %/ 17 % 25 %/ 17% 25 %/ 17% 20 %/ 15 % 55 %/ 40 % 50 %/ 35 %

100% duty cycle 220 - 240 V*

(25 / 40°) 55 A/ 35 A 60 A/ 40 A 55 A/ 35 A 50 A/ 35 A 85 A/ 60 A 90 A/ 65 A

Duty cycle at max.

output 380 - 415 V* (25 / 40°) 5 %/ 3 % 5 %/ 3 % 5 %/ 3 % 5 %/ 3 % 20 %/ 15 % 10 %/ 1,5 %

100% duty cycle 380 - 415 V*

(25 / 40°) - - - - - 90 A

Mains fuse 220 - 240 V 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag

Mains fuse 380 - 415 V 25 A time-lag 25 A time-lag 35 A time-lag 20 A time-lag 25 A time-lag 35 A time-lag

Cooling self self self self fan fan

Insulation class F F FFFF

Protection class IP 21 IP 21 IP 21 IP 21 IP 21 IP 23

Dimensions (lxwxh) in mm 440x230x430 440x230x430 440x230x430 550x330x380 550x330x380 550x330x380

Weight 27 kg 31 kg 35 kg 40 kg 44 kg 44 kg

Accessory kit no. 7 8 8 130 8 8

Max. electrode diameter 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm

2.1 Putting A combination 1-Ph/2-Ph Machine Into Operation

All "Combi" machines are supplied with a plug (CEE 5 pin 16/32 A) installed on the power cable. Connect to a 220 - 240 V

single-phase outlet with the adaptor supplied or to two phases of a 380/415 V 3-phase mains.

1.0 Specifications

- This welding machine should be connected to the power source via an Earth Fault Circuit Interrupter with 30 mA

capacity.

- Have worn or damaged power cables replaced immediately by a qualified electrician.

Do not operate the welding machine with a damaged power cable, danger of personal injury through electric shock.

- Children under the age of 16 should not operate this welding machine.

Connect to an earthed, single-phase 220 - 240 V outlet on a circuit protected by a 16 A time-lag fuse. Double insulated

machines (with PVC housing) do not require an earthed outlet. Operating other electrical machines or appliances on

the same circuit while welding is not recommended.

If your machine has detachable welding and earth cables, connect cables to the sockets, lock by turning plug clockwise.

With transformers the polarity does not matter, so both cables can be connected to either the + or - sockets. The same

applies for machines with permanently attached earth and welding cables.

Attach earth clamp to the work piece, close to the area to be welded and on to bare metal for good conduction. Place

a stick electrode into the electrode holder.

Set current selector switch to desired current. On all machines with stepless setting turn crank or handwheel until

desired current is indicated (stepless).

If there is no power outlet near the work piece an extension cable is required. The cable lead cross section must be

at least 2.5 mm

. The extension cable should be fully uncoiled to prevent heat build-up by inductance. Inductance also

considerably reduces the welding current. Extending the welding cables is also possible, however the cross section

of the extension cable should be larger than that of the cable supplied with the machine. Every machine is overload

protected by a thermo switch, which switches the transformer off if it becomes too hot. Let cool down until machine

switches on automatically. Some machines are equipped with a fan to increase the duty cycle through forced cooling.

The fan operates as long as the machine is switched on.

2.0 Putting A Single-Phase Machine Into Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elektra Beckum SK260 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info