Bedienungsanleitung Element4 Elite-E (Seite 8 von 28) (Englisch)

820605

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Chapter 6

INSTALLATION MANUAL |

6 INSTALLATION REQUIREMENTS

This product has been designed to be installed into a plaster board, or

existing masonry chimney breast.

Please seek advice from a professional, with reference to the structural

integrity of the installation site.

If the product is to be installed into a open chimney or ue, it is

important that the chimney/ue is blocked o to prevent any up/down

draughts and falling debris which could restrict and alter the airow to

the product.

It is also important to ensure that the product has a minimum internal

clearance directly above and below the product of 100mm, this is to

ensure that the product can circulate the required airow for the heater

unit. This is most important for the Elite 60I e as it's top surface can get

hot.

The product should never be sealed into a opening with the use of

silicones or adhesives as this can also alter the airow and hinder any

further servicing of the product.

Figure.6.1 | Beware, top of Elite 60I e can get hot

6�1 HEATER UNIT CUT OUT

This is a safety feature to safe guard against further damage to the

product.

If the airow is restricted the heater will automatically turn o. This can

occur due to incorrect installation or obstruction. To reset the heater

function;

• Isolate from main power supply

• Leave product to cool

• After suitable cooling down period, remove the obstruction if

obstructed and check installation

• After 10 minutes the thermo switch (cut-out) in the heater will

reset.

Please note: that both the eect fan and heater fan omit a low decibel

noise, both of which are normal operating characteristics.

6�2 SERVICING

Only a competent person should service this appliance. This appliance

must be serviced every 12 months.

Warning: Before carrying out any repairs or servicing, ensure that the

power supply cord is removed from the mains supply.

7 INSTALLATION METHOD

In all Element4 replaces, a free space of 100mm at least 50mm

must be maintained immediately above and below the main housing

for good air circulation. (Failure to do so may cause problems for the

heating and ame function).

Each Element4 replace is supplied with one or more wall mounting

brackets.

Determine the height at which the nished Element4 replace should

be positioned in relation to the oor level.

Note: The minimum distance to the oor is 300 mm

Attach the wall bracket to the wall, making sure that you use the correct

fasteners that match the respective wall - hollow or solid.

Hang the Element4 replace on the bracket and secure it in place with

the wall bracket at the top of the replace.

Insert the plug of the IEC-compliant power cable into the IEC-compliant

socket and ensure that it is rmly pushed.

Construct the hollow installation space for the electric re in the

desired dimensions. It is important that you take into account the

nished front when determining the depth of the frame construction.

It is important that a header/lintel is also placed at the desired height,

so that the weight of the wall made will not come to rest on the

appliance.

Make the cut in the plasterboard / nishing plate and install the

replace, making sure that the plaster board edges connect to the

inside of the cut in the plate.

Warning: In order to avoid a hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through an

external switching device, such as a timer, or connected to a circuit

that is regularly switched on and o by the utility.

7�1 PRODUCT SIZE

Theproduct dimensions can be found in APPENDIX BAPPENDIX B

It is also important to ensure that the product has a minimum clearance

around it of 15mm, this is to ensure that the product can circulate the

required airow to the heater unit.

The product should never be sealed into an opening with the use

of silicones or adhesives as this can alter the airow and hinder any

further servicing of the product.

Please refer to technical specication table for further information, with

reference to measurements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Element4 Elite-E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Element4 Elite-E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info