Bedienungsanleitung Elica Audrey Sense (Seite 37 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

649897

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Use

The hood has been made for use in the internal recirculating

filtering version.

Cooking fumes and steam are aspirated inside the hood,

filtered and cleaned, passing through the fat filter/s and the

carbon filter/s that MUST be supplied with the hood.

Important

It is possible to buy an extraction operation Kit.

In this case the charcoal filter must not be installed.

Furthermore, the use of the extraction kit may require a

different installation of the hood from what shown in this

manual; therefore, before starting the installation of the hood,

buy the extraction kit and consult the instructions enclosed

with the kit.

Installation

Specialised personnel must carry out both the electrical

and the mechanical installation.

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains tension must correspond to the tension shown on

the characteristic label situated inside the hood.

The product is meant for connecting directly to the mains

supply, therefore apply a regulation bipolar switch that

ensures complete disconnection from the mains in the

conditions of category III over-tension, conforming to the

installation rules.

Warning! Detail B (fixing bracket to the ceiling) is

equipped with a conductor (yellow-green) that must be

connected to the earth of the domestic electrical plant.

Fig. 16-17

ATTENTION! Be particularly careful about positioning

the excess cable. Failure to observe this indication could

cause grave damage to the apparatus and/or an electric

shock to the user or the installer.

Warining! Changing the interconnection cable must be

carried out by the authorised technical assistance service.

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• Remove the charcoal (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

Attention! Before connecting the hood to the electrical

mains.

If you have an Elica hob:

Perform the electrical connections of the hood and Elica

hob at the same time to ensure the logical connection

between the hob and Elica hob (also refer to the

paragraph "Operation-Adjusting the parameters for

automatic operation-Sensor calibration" e

"Operation-Adjusting the parameters for automatic

operation-Logical connection between hood and

Elica hob").

If you do NOT have an Elica hob:

In this case, after being connected to the mains, the hood

will try connecting to a hob.

Wait for the hob to complete the connection attempts

(approximately 5 minutes) and then disable the electronic

connection module as follows:

With the hob switched off, simultaneously press and hold

keys T1 and T2 for 10 seconds, (see Operation

paragraph), the hood at first emits a short sound signal

(beep- after approximately 5 seconds), followed by a long

sound signal (beeeep), indicating that the disabling

process is complete (LED L1 turns red for a few

seconds).

Reactivating the connection module between the

hood and Elica hob: With the hob switched off,

simultaneously press and hold keys T1 and T2 for 10

seconds, (see Operation paragraph), the hood at first

emits a short sound signal (beep- after approximately 5

seconds), followed by a long sound signal (beeeep),

indicating that the activation process is complete (LED L1

turns red for a few seconds).

This type of cooker hood must be fixed to the ceiling.

Very heavy product; hood handling and installation must

be carried out by at least two persons.

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough to

take the weight of the hood. Do not tile, grout or silicone

this appliance to the wall. Surface mounting only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Audrey Sense Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info