Bedienungsanleitung Elica Lien Diamond 604 (Seite 20 von 172) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

649920

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

Assembly

Before starting the installation:

• After unpacking the product, check that it was not

damaged during transport and in case of problems,

contact your dealer or Customer Service, before

proceeding with the installation.

• Check that the product is of the right size for the

installation location.

• Check for accessories inside the packaging (placed there

for ease of transport) such as bags containing screws,

the warranty card, etc. Remove them and keep them

safe.

• Also verify that near the area of installation there is an

electrical socket

Preparing the cabinet for installation:

- As the bottom of the product must not be accessible after

installation, a separator panel must always be installed

(for protection) under the hob (not supplied with the

product), if it is accessible after installation.

- If installing an oven under the top, do not interpose the

separator panel.

- If an oven is positioned under the induction hob it is

preferable that it is equipped with a cooling fan.

- Do not use the induction hob while the PYROLYTIC

cleaning of the oven is in operation.

- Avoid installing the hob above dishwashers or washing

machines so that the electronic circuits do not come into

contact with steam and moisture which could damage

them.

- The distance between the bottom of the device and the

partition panel (or any device installed below the induction

hob) must comply with the sizes indicated.

- To correctly operate the product, do not obstruct the

minimum opening between the worktop and the upper

side of the cabinet top.

- For adequate ventilation and to allow fresh air to circulate,

there must be openings in the kitchen cabinet, following

the dimensions indicated.

- Cut the cabinet before inserting the hob and carefully

remove shavings or sawdust.

Fig. 1a/1b

ATTENTION! Failure to install screws and fasteners in

accordance with these instructions may result in electrical

hazards.

Operation

Control panel

The hob has a smart and sophisticated wireless

communication system, able to communicate with some

special connectible Elica hoods. Depending on the use of the

hob and what you are cooking, such hoods receive

information from the surface, process it and automatically and

optimally activate so as to eliminate any waste. See

www.elica.com

to check the range of hoods connectible

with your hob.

Note: To select the commands, simply touch (press) the

symbols representing them.

Main Functions

1. Hob ON/OFF function

2. Timer

3. Operating level (power) adjustment and cooking

zone selection ring.

4. Pre-set operating level (power) selector

5. Cooking zone display*

6. Timer display

* The number and position of the displays varies depending on the

model of your hob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Lien Diamond 604 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info