Bedienungsanleitung Elica Lien Diamond 874 (Seite 17 von 169) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

649924

Zoom out

Zoom in

Vorherige Seite

1/169

Nächste Seite

Assembly

Before starting the installation:

• After unpacking the product, check that it was not damaged

during transport and in case of problems, contact your dealer

or Customer Service, before proceeding with the installation.

• Check that the product is of the right size for the installation

location.

• Check for accessories inside the packaging (placed there for

ease of transport) such as bags containing screws, the

warranty card, etc. Remove them and keep them safe.

• Also verify that near the area of installation there is an

electrical socket

Preparing the cabinet for installation:

- As the bottom of the product must not be accessible after

installation, a separator panel must always be installed (for

protection) under the hob (not supplied with the product), if it is

accessible after installation.

- If installing an oven under the top, do not interpose the

separator panel.

- If an oven is positioned under the induction hob it is preferable

that it is equipped with a cooling fan.

- Do not use the induction hob while the PYROLYTIC cleaning

of the oven is in operation.

- Avoid installing the hob above dishwashers or washing

machines so that the electronic circuits do not come into

contact with steam and moisture which could damage them.

- The distance between the bottom of the device and the

partition panel (or any device installed below the induction

hob) must comply with the sizes indicated.

- To correctly operate the product, do not obstruct the minimum

opening between the worktop and the upper side of the

cabinet top.

- For adequate ventilation and to allow fresh air to circulate,

there must be openings in the kitchen cabinet, following the

dimensions indicated.

- Cut the cabinet before inserting the hob and carefully remove

shavings or sawdust.

Fig. 1a/1b

ATTENTION! Failure to install screws and fasteners in accordance

with these instructions may result in electrical hazards.

Operation

Control panel

The hob has a smart and sophisticated wireless

communication system, able to communicate with some

special connectible Elica hoods. Depending on the use of the

hob and what you are cooking, such hoods receive

information from the surface, process it and automatically and

optimally activate so as to eliminate any waste. See

www.elica.com

to check the range of hoods connectible

with your hob.

Note: To select the commands, simply touch (press) the

symbols representing them.

Main Functions

1. Hob ON/OFF function

2. “Chef Cook” Function

3. “Lock” Function (if pressed together with 2.)

4. Timer activation (if pressed together with 5.) /Timer

Increase

5. Timer activation (if pressed together with 4) /Timer

Decrease

6. Timer display

7. Pre-set operating level (power) selector

8. Cooking zone display

9. Operating level (power) adjustment and cooking

zone selection bar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Lien Diamond 874 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info