Bedienungsanleitung Elica Personal-corner (Seite 8 von 10) (Englisch)

471224

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

the extensions with 2 screws and fix the deflector to the

flues support bracket with 4 screws.

5. Hook the hood onto the lower support bracket.

6. Insert the lower part of the hood to the suction unit and fix

with 6 screws.

Attention! The hood is not yet definitively fixed to the

wall, every successive operation must therefore be

carried out with caution to avoid the hood unhooking from

the support bracket and causing damage to people or

things.

7. Connect the electricity between the two parts.

8. To assemble the steam screen and the flue-centring

bracket, use the screws and bushes supplied.

9. Fix the flue-centring steam screen - bracket unit above

the hood.

10. Adjust the distance of the hood from the wall and the

horizontal set of the hood with the 2 adjustment screws

on the hooks of the hood.

11. a. Definitely fix the steam screen-flue centring bracket

with 2 screws.

b. Additional small adjustments of the position of the

steam screen can be made loosening the 6screws from

inside the hood. Once the adjustment has been

completed, tighten the 6 screws up again.

12. Fix the motor unit to the support structure definitively:

make a Ø2.5 mm pilot hole on the support structure with

a drill, passing through the lower hole inside the motor

housing, after which fix definitively with 1 screw and

washer.

13. Carry out the connection of a tube (tube and strips for

fixing not supplied, to be purchased) for the discharge of

fumes to the connection ring over the suction motor unit.

The other end of the tube must be connected to a device

for the expulsion of fumes outside in the case of using

the hood in the suction version or to deflector F in the

case of using the hood in the filtering version.

14. Connect the electricity.

15. Apply the flues to cover the discharge tube, making the

plate extrude from the slot of the lower section of the flue.

Note: check that the tongues of the lower section of the

flue enter under the tongues of the centring bracket,

blocking it.

16. Fix with 2 screws.

17. Extract the upper part of the flue and fix it to the flues

support bracket „G“ with 2 screws.

18. Connect the plate to the control panel and fix it to the

rectangular slot (flush fixing).

Mount the frame of the carbon filter and the fats filter/s again

and check the perfect functioning of the hood.

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour screen

6. Telescopic chimney

7. Air outlet (used for filter version only)

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

A. on/off light switch.

B. on/off aspiration switch and minimum

power selection

B+C.medium power selection aspiration

switch

B+D.maximum power selection aspiration

switch

Maintenance

Before performing any maintenance operation, isolate the

hood from the electrical supply by switching off at the

connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products.

DO NOT USE ALCOHOL!

Grease filter

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To remove the grease filter, pull the spring release handle.

Fig. 2

Charcoal filter (filter version only)

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months (or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Personal-corner Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info