Bedienungsanleitung Elica Sienna (Seite 9 von 10) (Englisch)

471227

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Instruction on mounting and use

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set out

in this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

Use

The hood has been made for use in the internal recirculating

filtering version.

Cooking fumes and steam are aspirated inside the hood,

filtered and cleaned, passing through the fat filter/s and the

carbon filter/s that MUST be supplied with the hood.

Attention!

If the hood is not supplied with carbon filter, then it

must be ordered and mounted.

Installation

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 50cm from electric cookers and

70 cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The electrical tension must correspond to the tension noted

on the label placed inside the cooker hood. Connect the

electrical plug, where provided, to the an easily accessible

outlet in conformity with local standards in force. Where an

electrical plug is not provided (for direct connection to

electrical network) place a standards approved bipolar switch

with an aperture distance of not less than 3mm (accessible)

from the contacts.

Attention: substituting the supply cable must be carried out

by the authorised technical assistance service.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Description of the hood

Fig. 1

A. Dowels for fixing the support bracket

B. Support to the ceiling bracket

C. Screws for fixing the support bracket

D. Regulators of the tie-rods of the hood

E. Decorative cover

F. Box for connecting to the domestic power network

G. Cable block

H. Electric cable

I. Lateral moulding

J. Suction hood

K. Panel of control

L. Halogen bulb

M. Lateral filter holder frame

N. Active carbon filter

O. Metal anti-fat filter

Note: other carbon and anti-fat filters are installed inside

the hood in correspondence with the shaped lateral slots

and the upper part of the hood (see also Figs. 11-a-b-c-d-

e-f-g-h)

P. Anti-fat and carbon filters holder frame

Q. Filter holder frame releases

R. Screws for fixing the cable block and the cover of the

connections box

S. Screws for fixing the connections box to the support

bracket

T. Tie-rod blocks

U. Tie-rods

V. Tie-rod connection brackets

W. Screws for fixing the tie-rod connection brackets

X. Screws for fixing the bracket cover

Y. Fixing template.

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Rotate the control bar clockwise to switch the light on and

select the various suction speeds (power) the hood is

equipped with.

Rotate anti-clockwise to reduce or switch off the hood and the

light.

Maintenance

Prior to any maintenance operation ensure that the cooker

hood is disconnected from the power supply.

Cleaning

The cooker hood should be cleaned regularly internally and

externally. Clean using the cloth dampened with neutral liquid

detergent. Do not use abrasive products.

DO NOT USE ALCOHOL!

Warning: Failure to carry out the basic standards of the

cleaning of the cooker hood and replacement of the filters may

cause fire risks.

Therefore we recommend observing these instructions.

Grease filter

Fig. 11

This must be cleaned once a month using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle. When washed

in a dishwasher, the grease filter may discolour slightly, but

this does not affect its filtering capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Sienna Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info