Bedienungsanleitung Elica Space (Seite 12 von 15) (Englisch)

471173

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Installation without flue

1. Use a pencil to mark the line representing the centre of

the appliance on the wall, as far as the ceiling. This will

make the installation process easier.

2. Position the drilling template on the wall: the vertical

centre line printed on the template should be aligned with

the centre line marked on the wall, and the lower edge of

the template should line up with the lower edge of the

cooker hood.

3. Rest the lower support bracket on the drilling template,

making sure it coincides with the sketched rectangle,

then mark the two outer holes and drill them.

Note: Always make the holes indicated on the template:

the 2 upper holes are used to position the hood, while the

lower holes generally 1 central or several at the sides)

are used to fix it in place and secure it properly.

Remove the drilling template, insert the rawl plugs and fix

the cooker hood support bracket in place using 2 screws

measuring 5x45 mm.

4. Hang the cooker hood on the lower bracket.

5. Adjust the distance between the cooker hood and the

wall.

6. Adjust the horizontal position of the cooker hood.

7. Fix the cooker hood to the wall securely

COMPULSORY!!).

Ducting version.

Connect a tube tube and fixing clamps not supplied;

these are to be purchased separately) for the expulsion

of smoke to the connection ring located above the

suction motor assembly.

The other end of the tube should be connected to a

device for the expulsion of smoke outdoors if the cooker

hood is to be used as a ducted version.

Filter version.

Remove the air outlet connection and apply the anti-

intrusion grille.

Attention! If the hood is not supplied with carbon

filter, then it must be ordered and mounted.

9.Slot the front panel in and perform the necessary

electrical connections for the control panel.

10. Fix the front panel in place using 6 screws 3 per side).

11. Slot in the side panels and fix them in place by sliding

them downwards.

12. Position the upper fixing bracket and secure it using 2

screws.

13. Perform all necessary electrical connections.

Remount the carbon filter frame and the fat/s filter/s and check

the perfect functioning of the hood.

Installation with flue

1. Use a pencil to mark the line representing the centre of

the appliance on the wall, as far as the ceiling. This will

make the installation process easier.

2. Position the drilling template on the wall: the vertical

centre line printed on the template should be aligned with

the centre line marked on the wall, and the lower edge of

the template should line up with the lower edge of the

cooker hood.

3. Rest the lower support bracket on the drilling template,

making sure it coincides with the sketched rectangle,

then mark the two outer holes and drill them.

Note: Always make the holes indicated on the template:

the 2 upper holes are used to position the hood, while the

lower holes generally 1 central or several at the sides)

are used to fix it in place and secure it properly.

Remove the drilling template, insert the rawl plugs and fix

the cooker hood support bracket in place using 2 screws

measuring 5x45 mm.

4. Place the flue support bracket “G” on the wall so that it is

against the ceiling, use the flue support bracket as a

drilling template if present, the small slot on the support

should coincide with the line made previously on the wall)

and use a pencil to mark 2 holes, then drill them Ø 8

mm) and insert 2 rawl plugs.

5. Fix the flue support bracket to the wall using 2 screws

measuring 5x45 mm.

6. Hang the cooker hood on the lower bracket.

7. Adjust the distance between the cooker hood and the

wall.

8. Adjust the horizontal position of the cooker hood.

9. Fix the cooker hood to the wall securely

COMPULSORY!!).

10. Connect a tube tube and fixing clamps not supplied;

these are to be purchased separately) for the expulsion

of smoke to the connection ring located above the

suction motor assembly.

The other end of the tube should be connected to a

device for the expulsion of smoke outdoors if the cooker

hood is to be used as a ducted version. If you wish to use

the cooker hood as a filter version, fix deflector F to flue

support bracket G and connect the other end of the tube

to the connection ring located under deflector F.

11. Perform all necessary electrical connections.

12. Position the flue.

13. Fix the flue to the flue support bracket G using 2 screws.

14. Slot the front panel in and perform the necessary

electrical connections for the control panel.

15. Fix the front panel in place using 6 screws 3 per side).

16. Slot in the side panels and fix them in place by sliding

them downwards.

17. Position the upper fixing bracket and secure it using 2

screws.

Remount the carbon filter frame and the fat/s filter/s and check

the perfect functioning of the hood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Space Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elica Space

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info