Bedienungsanleitung Elica Stone Gallery (Seite 6 von 8) (Englisch)

471177

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Installation

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 50cm from electric cookers and

65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area. If it not fitted

with a plug (direct mains connection) or if the plug is not

located in an accessible area apply a double pole switch in

accordance with standards which assures the complete

disconnection of the mains under conditions relating to over-

current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• To facilitate installation, remove the fat filters and the

other parts allowed and described here, dismantle and

mount it.

To remove see also the relative paragraphs.

• Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

• Disconnect the hood during electrical connection, by

turning the home mains switch off.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Attention! The chimney is predisposed for installation of

the filter Version.

In certain models where it is required to use the cooker hood

in the suction version then it is possible to overturn the upper

section of the chimney

and insert it inside the lower section of the chimney so that the

air-exit perforations are not visible.

The chimneys in which this operation is possible are

recognizable by their bracket fixing points G which are

repeated also in the lower side of the upper section of the

chimney.

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Fig. 5

1. Draw a line on the wall up to the ceiling with a pencil,

corresponding to the centre line. It will make the operations

easier.

2. Apply the drilling template to the wall: the vertical centre

line printed on the drilling template should correspond to

the centre line drawn on the wall. In addition, the lower

edge of the hole drilling template corresponds to the

lower edge of the hood.

3. Put the lower support bracket on the drilling template,

making it coincide with the traced triangle, marking the

two external holes and drill.

Note: Always make all the holes indicated on the

template.

4. Remove the drilling template, insert the wall dowels into

all the holes made and fix the support bracket of the hood

with two screws.

5. Apply flues support bracket „G“ to the wall joining the

ceiling. Use the support bracket of the hood as a drilling

template (if present, the small slot on the support must

coincide with the line previously traced on the wall) and

mark 2 holes with a pencil. Drill the holes and insert 2

dowels.

6. Fix the flues support bracket to the wall with 2 screws.

7. Hook the hood to the bracket.

8. Adjust the distance of the hood from the wall.

9. Adjust the horizontal setting of the hood.

10. Fix the hood to the wall definitively (COMPULSORY!!).

11. Extract the sliding supports and block them with 2

screws.

12. Hook the front panel to the support, adjust the slope and

fix it with 4 screws (2 per side).

13. Unscrew the sliding supports fixing screws and adjust the

depth of the panel.

Fix the panel in the wanted position with the 4 screws.

14. Connect a tube (tube and fixing bands not supplied: to be

purchased.) for discharging the fumes to the connection

ring placed over the suction motor unit.

The other end of the tube must be connected to a fumes

expulsion device toward the exterior of the house if using

Elica Stone Gallery Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elica Stone Gallery

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info